Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2013 Ford Fusion Energi TitaniumFACTORY OEM SERVICE PROCEDURE
Occupant Classification System Module (OCSM) DTC Chart
OCSM DTC CHART
| DTC | Description | Action |
|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short To Ground | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short To Battery | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:1C | Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:49 | Passenger Seatbelt Tension Sensor: Internal Electronic Failure | REFER to: PINPOINT TEST - DTC: KK . |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short to Ground | INSPECT the OCSÂ
sensor pressure hose and pressure hose routing. VERIFY the hose is not twisted, pinched or damaged and that the hose is routed correctly. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . If a concern is found, REPAIR as needed. If no concern is found, CYCLE the ignition and REPEAT the OCSMÂ self-test. If DTCÂ B00C0:11 returns, INSTALL a new OCSÂ sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C0:1A | Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:11 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Ground | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:12 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Battery | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:49 | Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | REFER to: PINPOINT TEST - DTC: LL . |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | REFER to: PINPOINT TEST - DTC: LL . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | CLEAR the OCSMÂ
Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTCÂ
B1193:00 returns, INSTALL a new OCSÂ
sensor. INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U0100:00 | Lost Communication with ECM/PCM A: No Sub Type Information | REFER to: PINPOINT TEST - DTC: SS . |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | REFER to: PINPOINT TEST - DTC: NN . |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | CARRY OUT the PCMÂ self-test. REFER to the ENGINE CONTROLS - INTRODUCTION (HYBRID) (SECTION 0) or the appropriate article. Refer to the appropriate engine article for the procedure. |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3000:54 | Control Module: Missing Calibration | Using a diagnostic scan tool, CARRY OUT the OCSÂ
Reset. FOLLOW all instructions on the diagnostic scan tool. If the OCSÂ
Reset was not successful, VERIFY correct installation of the OCSÂ
. VERIFY the pressure sensor hose is correctly routed and CORRECT the installation as necessary. REPEAT the self-test. If DTCÂ
U3000:54 is still present, INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | REFER to: PINPOINT TEST - DTC: JJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | REFER to: PINPOINT TEST - DTC: JJ . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
