2013 Ford Fiesta Titanium, 4D Hatchback, Standard TransFACTORY OEM SERVICE PROCEDURE

Audio Front Control Module (ACM)

AUDIO FRONT CONTROL MODULE (ACM) DTC CHART

DTC Description Action
B1A01:01 Speaker #1: General Electrical Failure GO to PINPOINT TEST F .
B1A01:11 Speaker #1: Circuit Short to Ground GO to PINPOINT TEST F .
B1A01:12 Speaker #1: Circuit Short to Battery GO to PINPOINT TEST F .
B1A01:13 Speaker #1: Circuit Open GO to PINPOINT TEST F .
B1A02:01 Speaker #2: General Electrical Failure GO to PINPOINT TEST F .
B1A02:11 Speaker #2: Circuit Short to Ground GO to PINPOINT TEST F .
B1A02:12 Speaker #2: Circuit Short to Battery GO to PINPOINT TEST F .
B1A02:13 Speaker #2: Circuit Open GO to PINPOINT TEST F .
B1A03:01 Speaker #3: General Electrical Failure GO to PINPOINT TEST F .
B1A03:11 Speaker #3: Circuit Short to Ground GO to PINPOINT TEST F .
B1A03:12 Speaker #3: Circuit Short to Battery GO to PINPOINT TEST F .
B1A03:13 Speaker #3: Circuit Open GO to PINPOINT TEST F .
B1A04:01 Speaker #4: General Electrical Failure GO to PINPOINT TEST F .
B1A04:11 Speaker #4: Circuit Short to Ground GO to PINPOINT TEST F .
B1A04:12 Speaker #4: Circuit Short to Battery GO to PINPOINT TEST F .
B1A04:13 Speaker #4: Circuit Open GO to PINPOINT TEST F .
B1A56:1D Antenna: Circuit Current Out of Range GO to PINPOINT TEST A .
B1A56:21 Antenna: Signal Amplitude < Minimum If DTC B1A56:21 sets after running the bezel diagnostic tests, disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail. Therefore, tests ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded.
B1A89:11 Satellite Antenna: Circuit Short to Ground GO to PINPOINT TEST B .
B1A89:13 Satellite Antenna: Circuit Open GO to PINPOINT TEST B .
B1D19:4B Compact Disc Unit: Over Temperature The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation.
U0140:00 Lost Communication With The BCM: No Sub Type Information GO to PINPOINT TEST P .
U0253:00 Lost Communication With Accessory Protocol Interface Module: No Sub Type Information GO to PINPOINT TEST Q .
U0257:00 Lost Communication With Front Controls/Display Interface Module: No Sub Type Information GO to PINPOINT TEST R .
U2100:00 Initial Configuration Not Complete: No Sub Type Information
  • This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM.
  • If there have been recent service actions with the ACM, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM .
  • If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information
  • This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM.
  • If there have been recent service actions with the ACM, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM .
  • If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) .
U3000:41 Control Module: General Checksum Failure CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation.
U3000:42 Control Module: General Memory Failure CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation.
U3000:49 Control Module: Internal Electronic Failure CLEAR the DTCs. REPEAT the self-test. If DTC U3000:49 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation.
U3000:96 Control Module: Component Internal Failure GO to PINPOINT TEST C .
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to PINPOINT TEST S .
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to PINPOINT TEST T .
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.