2013 Ford F-150 Limited, RWDFACTORY OEM SERVICE PROCEDURE

Front Control Interface Module (FCIM)

FCIM DTC CHART

DTC Description Action
B00D5:01 Restraint System Passenger Disable Indicator: General Electrical Failure
B113C:11 Hazard switch illumination: Circuit Short To Ground
B1202:01 Restraint System Passenger Enable Indicator: General Electrical Failure
U0155:00 Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information GO to PINPOINT TEST AF .
U0257:00 Lost Communication With Front Controls / Display Interface Module: No Sub Type Information GO to PINPOINT TEST AL .
U0423:00 Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information RETRIEVE and FOLLOW DTCs present in the IPC. REFER to INFORMATION CENTER - INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES .
U2013:63 Switch Pack: Circuit / Component Protection Time-Out
U3000:41 Control Module: General Checksum Failure
U3000:42 Control Module: General Memory Failure
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to PINPOINT TEST AM .
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to PINPOINT TEST AN .
U0100:00 Lost Communication with ECM/PCM "A": No Sub Type Information GO to PINPOINT TEST AC .
U0140:00 Lost Communication With Body Control Module: No Sub Type Information: No Sub Type Information GO to PINPOINT TEST AD .
U0155:00 Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information GO to PINPOINT TEST AF .
U0401:00 Invalid Data Received from ECM/PCM A: No Sub Type Information RETRIEVE and FOLLOW DTCs present in the PCM. REFER to ELECTRONIC ENGINE CONTROLS .
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information RETRIEVE and FOLLOW DTCs present in the BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES .
U0423:00 Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information RETRIEVE and FOLLOW DTCs present in the IPC. REFER to INFORMATION CENTER - INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES .
U2100:00 Initial Configuration Not Complete: No Sub Type Information CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. For more information, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM . If there have been no recent service actions, INSTALL a new Global Positioning System Module (GPSM) to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. For more information, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM . If there have been no recent service actions, INSTALL a new Global Positioning System Module (GPSM) to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:09 Control Module: Component Failure
  • CLEAR the DTC.
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC U3000:09 is retrieved again, PERFORM a battery reset by disconnecting the battery for 5 minutes, then reconnecting it.
  • CLEAR the DTC.
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC U3000:09 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:41 Control Module: General Checksum Failure
  • CLEAR the DTC.
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC U3000:41 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:42 Control Module: General Memory Failure
  • CLEAR the DTC.
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC U3000:42 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to PINPOINT TEST AM .
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to PINPOINT TEST AN .
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.