Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2013EXPLORER POLICE INTERCEPTOR, FWDREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEXANTI-THEFT SYSTEM DTCSPASSIVE ANTI-THEFT WITH INTELLIGENT ACCESSRFA MODULE
2013 Ford Explorer Police Interceptor, FWD
RFA Module
2013 Ford Explorer Police Interceptor, FWDSECTION RFA Module
DTC DESCRIPTION - RFA MODULE
| DTC | Description | Action |
|---|---|---|
| B10C7:01 | PATS Target Identifier: Not Programmed | GO to PINPOINT TEST D . |
| B10C8:01 | Interior Centre Antenna: General Electrical Failure | GO to PINPOINT TEST D . |
| B10C9:01 | Interior Front Antenna: General Electrical Failure | GO to PINPOINT TEST D . |
| B10D7:05 | PATS Key: System Programming Failure | GO to PINPOINT TEST A . |
| B10D7:31 | PATS Key: No Signal | This DTC sets during an RFA module self-test if 2 programmed Intelligent Access (IA) keys are not detected inside the vehicle. CHECK each IA key individually to see if it operates the vehicle. If an IA key does not operate the vehicle, PROGRAM that key. Key Programming Using Diagnostic Equipment . If 2 programmed IA keys are not present inside the vehicle, DISREGARD this DTC. |
| B10D8:51 | PATS Key Less Than Minimum Programmed: Not Programmed | If other PATS DTCs are present, address them first. If DTC B10D8:51 is the only DTC present, PROGRAM additional keys (minimum of 2 keys must be programmed). Key Programming Using Diagnostic Equipment . CLEAR the DTCs. REPEAT the self-test. |
| B10D9:11 | PATS Transponder: Circuit Short To Ground | GO to PINPOINT TEST B . |
| B10D9:12 | PATS Transponder: Circuit Short To Battery | GO to PINPOINT TEST B . |
| B10D9:31 | PATS Transponder: No Signal | GO to PINPOINT TEST B . |
| B10D9:87 | PATS Transponder: Missing Message | GO to PINPOINT TEST B . |
| B10DA:51 | PATS PCM Identifier: Not Programmed | There is no BCM ID stored in the RFA module. CARRY OUT a parameter reset, Refer to Passive Anti-Theft System (PATS) Parameter Reset , then CYCLE the ignition and make an attempt to start the vehicle. CLEAR the DTCs . REPEAT the self-test. |
| B10DA:61 | PATS PCM Identifier: Signal Calculation Failure | There is an incorrect BCM ID stored in the RFA module. CARRY OUT a parameter reset, Refer to Passive Anti-Theft System (PATS) Parameter Reset , then CYCLE the ignition and make an attempt to start the vehicle. CLEAR the DTCs . REPEAT the self-test. |
| U201F:31 | External Receiver: No Signal | GO to PINPOINT TEST C . |
| All other RFA module DTCs | - | REFER to DTC CHART: RFA . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.