Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2013EXPLORER POLICE INTERCEPTOR, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE MECHANICALEXHAUST SYSTEMSPECIFICATIONSTORQUE SPECIFICATIONS
2013 Ford Explorer Police Interceptor, AWD
Torque Specifications
2013 Ford Explorer Police Interceptor, AWDSECTION Torque Specifications
TORQUE SPECIFICATIONS
| Description | Part Number | Torque |
|---|---|---|
| Catalytic converter-to-bracket nuts | Part of 5E211 | 25 Nm (18 lb-ft) |
| Catalytic converter-to-turbocharger clamp (2.0L GTDI ) | 5A231 | 20 Nm (177 lb-in) |
| EPAS shield | W505252 | 9 Nm (80 lb-in) |
| Exhaust flexible pipe nuts | W714265 | 40 Nm (30 lb-ft) |
| Exhaust Y-pipe-to-muffler and tailpipe flange nuts | W714265 | 40 Nm (30 lb-ft) |
| Exhaust Y-pipe-to-LH catalytic converter manifold nuts | W714265 | Refer to EXHAUST Y-PIPE - 3.5L TI-VCT or Refer to EXHAUST Y-PIPE - 3.7L TI-VCT |
| Exhaust Y-pipe-to-RH catalytic converter nuts | W714265 | Refer to EXHAUST Y-PIPE - 3.5L TI-VCT or Refer to EXHAUST Y-PIPE - 3.7L TI-VCT |
| LH and RH catalytic converter manifold heat shield bolts | W703715 | 10 Nm (89 lb-in) |
| LH exhaust flexible pipe-to-LH catalytic converter nuts (3.5L GTDI | W714265 | Refer to EXHAUST FLEXIBLE PIPE - LH, 3.5L GTDI |
| RH exhaust flexible pipe-to-RH catalytic converter nuts (3.5L GTDI | W714265 | 40 Nm (30 lb-ft) |
| LH catalytic converter manifold-to-cylinder head nuts | W716011 | Catalytic Converter - LH Manifold |
| LH and RH catalytic converter manifold-to-cylinder head studs | W712244 | 12 Nm (106 lb-in) |
| LH and RH catalytic converter-to-turbocharger nuts | W714265 | Refer to CATALYTIC CONVERTER - LH, 3.5L GTDI or Refer to CATALYTIC CONVERTER - RH, 3.5L GTDI |
| LH and RH turbocharger-to-catalytic converter studs | W712458 | 25 Nm (18 lb-ft) |
| LH catalytic converter manifold support bracket-to-transmission bolts | W710656 | 48 Nm (35 lb-ft) |
| RH catalytic converter manifold-to-cylinder head nuts | W716011 | Refer to CATALYTIC CONVERTER - RH MANIFOLD |
| Skid plate (if equipped) | 70 Nm (52 lb-ft) | |
| Torca® clamp | 5221 | 55 Nm (41 lb-ft) |
| Worm gear clamp | 5221 | 7 Nm (62 lb-in) |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.