Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2013 Ford Escape Titanium, FWDFACTORY OEM SERVICE PROCEDURE
Front Control/Display Interface Module (FCDIM)
FRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B10BD:11 | Multifunctional Switch: Circuit Short to Ground | GO to PINPOINT TEST D . |
| B10BD:13 | Multifunctional Switch: Circuit Open | GO to PINPOINT TEST D . |
| B10BD:23 | Multifunctional Switch: Signal Stuck Low | GO to PINPOINT TEST D . |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST Q . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST R . |
| U0193:00 | Lost Communication With Digital Audio Control Module A: No Sub Type Information | GO to PINPOINT TEST S . |
| U0423:68 | Invalid Data Received From Instrument | Panel Cluster (IPC) Control Module: Event Information REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES , to retrieve and follow DTCs present in the IPC. |
| U1A00:00 | Private Communication Network: No Sub Type Information | GO to PINPOINT TEST G . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U3000:00 | Control Module: No Sub Type Information | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:00 is still present, INSTALL a new Front Control/Display Interface Module (FCDIM). REFER to FRONT CONTROLS/DISPLAY INTERFACE MODULE (FCDIM) . |
| U3006:16 | Control Module Input Power "A": Circuit Voltage Below Threshold | GO to PINPOINT TEST I . |
| U3006:17 | Control Module Input Power "A": Circuit Voltage Above Threshold | GO to PINPOINT TEST J . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.