2012 Ford Transit Connect L4-2.0LFACTORY OEM SERVICE PROCEDURE

Timing Chain: Service and Repair




Timing Drive Components

Removal

NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed. The crankshaft pulley and the crankshaft timing sprocket are not keyed to the crankshaft. The crankshaft, the crankshaft sprocket and the pulley are fitted together by friction, using diamond washers between the flange faces on each part. For that reason, the crankshaft sprocket is also unfastened if the pulley bolt is loosened. Before any repair requiring loosening or removal of the crankshaft pulley bolt, the crankshaft and camshafts must be locked in place by the special service tools, otherwise severe engine damage can occur.

NOTICE: During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan can cause engine failure.

1. With the vehicle in NEUTRAL, position it on a hoist.

2. Remove the engine front cover. For additional information, refer to Engine Front Cover Service and Repair.

3. Compress the timing chain tensioner in the following sequence.
1. Using a small pick, release and hold the ratchet mechanism.

2. While holding the ratchet mechanism in the released position, compress the tensioner by pushing the timing chain arm toward the tensioner.

3. Insert a paper clip into the hole to retain the tensioner.


Factory service manual diagram




4. Remove the 2 bolts and the timing chain tensioner.

Factory service manual diagram




5. Remove the RH timing chain guide.

Factory service manual diagram




6. Remove the timing chain.

Factory service manual diagram




7. Remove the bolts and the LH timing chain guide.

Factory service manual diagram




8. NOTICE: Do not rely on the Camshaft Alignment Plate to prevent camshaft rotation. Damage to the tool or the camshaft can occur.

NOTE: Intake camshaft drive gear shown, exhaust camshaft drive gear similar.

Remove the bolts and the camshaft drive gears.
- Use the flats on the camshaft to prevent camshaft rotation.


Factory service manual diagram




Installation

1. Install the camshaft drive gears and the bolts. Do not tighten the bolts at this time.

Factory service manual diagram




2. Install the LH timing chain guide and bolts.
- Tighten to 10 Nm (89 lb-in).


Factory service manual diagram




3. Install the timing chain.

Factory service manual diagram




4. Install the RH timing chain guide.

Factory service manual diagram




NOTE: If the timing chain tensioner plunger and ratchet assembly are not pinned in the compressed position, follow the next 4 steps.

5. NOTICE: Do not compress the ratchet assembly. This will damage the ratchet assembly.

Using the edge of a vise, compress the timing chain tensioner plunger.


Factory service manual diagram




6. Using a small pick, push back and hold the ratchet mechanism.

Factory service manual diagram




7. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.

Factory service manual diagram




8. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and the plunger in during installation.

Factory service manual diagram




9. Install the timing chain tensioner and the 2 bolts.
- Tighten to 10 Nm (89 lb-in).

- Remove the paper clip to release the piston.


Factory service manual diagram




10. NOTICE: The Camshaft Alignment Plate is for camshaft alignment only. Using this tool to prevent engine rotation can result in engine damage.

Using the flats on the camshafts to prevent camshaft rotation, tighten the camshaft drive gear bolts.
- Tighten to 72 Nm (53 lb-ft).


Factory service manual diagram




11. Install the front cover. For additional information, refer to Engine Front Cover Service and Repair.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.