Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Test Procedure
- RI1 PRELIMINARY DIAGNOSISÂ
Are DTCs P2043, P205C or P205D present?Â
Yes No For DTC P2043, GO to  RI2.
For DTCs P205C or P205D, GO to  RI3.Unable to duplicate the condition. CHECK for a loose connection, and damaged or corroded terminals. WIGGLE the harness attempting to recreate the concern. REPAIR as necessary.
REFER to NO DIAGNOSTIC TROUBLE CODES (DTCS) PRESENT SYMPTOM CHART INDEX , if a driveability concern exists. - RI2 CHECK THE REDUCTANT TEMPERATURE SENSOR OPERATIONÂ
- Verify the engine temperature is at ambient room temperature before continuing with this test. A soak period of 6 hours may be required.
- Ignition ON, engine OFF.
- Access the PCM and monitor the REDUCT_TNK_T (TEMP) PID.
Does the PID temperature match ambient temperature?Â
Yes No Unable to duplicate the condition. CHECK for a loose connection, and damaged or corroded terminals. WIGGLE the harness attempting to recreate the concern. REPAIR as necessary.
REFER to NO DIAGNOSTIC TROUBLE CODES (DTCS) PRESENT SYMPTOM CHART INDEX , if a driveability concern exists.INSTALL a new Reductant Heater and Sender assembly. REFER to the Engine Emission Control article.
Clear the PCM DTCs. REPEAT the self-test. - RI3 CHECK THE REDUCTANT TEMPERATURE SENSOR CIRCUITS FOR AN OPENÂ
- Ignition OFF.
- Reductant Heater and Sender Assembly connector disconnected.
- PCM-T connector disconnected.
- Measure the resistance between:
(+) Reductant Heater and Sender Assembly Connector, Harness Side (-) PCM-T Connector, Harness Side RDT - Pin 3 RDT - Pin 8 RDLRTN - Pin 5 RDLRTN - Pin 32
Are the resistances less than 5 ohms?Â
Yes No GO to  RI4. REPAIR the open circuit. Clear the PCM DTCs.
REPEAT the self-test. - RI4 CHECK THE REDUCTANT TEMPERATURE SENSOR CIRCUITS FOR A SHORT TO GROUNDÂ
- Measure the resistance between:
(+) PCM-T Connector, Harness Side (-) RDT - Pin 8 Ground RDLRTN - Pin 32 Ground
Are the resistances greater than 10K ohms?Â
Yes No GO to  RI5. REPAIR the short circuit. Clear the PCM DTCs.
REPEAT the self-test. - Measure the resistance between:
- RI5 CHECK THE REDUCTANT TEMPERATURE SENSOR CIRCUITS FOR A SHORT TO VOLTAGEÂ
- Ignition ON, engine OFF.
- Measure the voltage between:
(+) PCM-T Connector, Harness Side (-) RDT - Pin 8 Ground RDLRTN - Pin 32 Ground
Is any voltage present?Â
Yes No REPAIR the short circuit. Clear the PCM DTCs.
REPEAT the self-test.GO to  RI6. - RI6 CHECK THE RESISTANCE OF THE REDUCTANT TEMPERATURE SENSORÂ
- Measure the resistance between:
(+) Reductant Heater and Sender Assembly Connector, Component Side (-) Reductant Heater and Sender Assembly Connector, Component Side RDT - Pin 3 RDLRTN - Pin 5
Is the resistance between 1.1K - 300K ohms?Â
Yes No GO to  RI7. INSTALL a new Reductant Heater and Sender assembly. REFER to the appropriate Engine Emission Control article.
Clear the PCM DTCs. REPEAT the self-test. - Measure the resistance between:
- RI7 CHECK FOR CORRECT PCM OPERATIONÂ
- Disconnect all the PCM connectors.
- Visually inspect for:
- pushed out pins
- corrosion
- Connect all the PCM connectors and make sure they seat correctly.
- Carry out the PCM self-test.
- Verify the concern is still present.
Is the concern still present?Â
Yes No INSTALL a new PCM. REFER to FLASH ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY (EEPROM) . The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
