2012 Ford Taurus SEFACTORY OEM SERVICE PROCEDURE

Symptom Chart

WARNING: This page is about a different car, the 2010 Lincoln MKX and 2010 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.
SYMPTOM CHART

Condition Possible Sources Action
  • The vehicle does not start with the scan tool connected to the Data Link Connector (DLC) and/or multiple malfunction indicators are only on when the scan tool is connected to the DLC  .
  • Wiring, terminals or connectors
  • Scan tool
  • The PCM does not respond to the scan tool
  • Wiring, terminals or connectors
  • PCM
  • The ABS module does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • ABS module
  • The Restraints Control Module (RCM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • Case ground open
  • RCM  .
  • The 4X4 control module does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • 4X4 control module
  • The Occupant Classification System Module (OCSM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • OCSM 
  • The Headlamp Control Module (HCM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • HCM 
  • The Steering Angle Sensor Module (SASM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • SASM 
  • The Instrument Cluster (IC) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • IC 
  • The Smart Junction Box (SJB) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • SJB  .
  • The HVAC module does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • HVAC module
  • The Audio Control Module (ACM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • ACM  .
  • The audio Digital Signal Processing (DSP) module does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • Audio DSP  module
  • The Satellite Digital Audio Receiver System (SDARS) module does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • SDARS  module
  • The Liftgate/Trunk Module (LTM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • LTM 
  • The Driver Seat Module (DSM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • DSM  .
  • The Global Positioning System Module (GPSM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • GPSM 
  • The Dual Climate Controlled Seat Module (DCSM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • DCSM 
  • The Parking Aid Module (PAM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • PAM 
  • The Accessory Protocol Interface Module (APIM) does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • APIM  .
  • Intermittent no Medium Speed Controller Area Network (MS-CAN) communication, one or more modules are not responding during network test
  • Wiring, terminals or connectors
  • DLC 
  • No Medium Speed Controller Area Network (MS-CAN) communication, all modules are not responding
  • Wiring, terminals or connectors
  • DLC 
  • ACM  .
  • APIM  .
  • Audio DSP  module (if equipped)
  • DCSM  (if equipped)
  • DSM  (if equipped)
  • GPSM  (if equipped)
  • HVAC module (if equipped)
  • IC 
  • LTM  (if equipped)
  • PAM  (if equipped)
  • SDARS  module (if equipped)
  • SJB  .
  • Intermittent no High Speed Controller Area Network (HS-CAN) communication, one or more modules are not responding during network test
  • Wiring, terminals or connectors
  • DLC 
  • No High Speed Controller Area Network (HS-CAN) communication, all modules are not responding
  • Wiring, terminals or connectors
  • DLC 
  • 4X4 control module (if equipped)
  • ABS module
  • APIM  .
  • HCM  (if equipped)
  • IC 
  • OCSM 
  • PCM
  • RCM  .
  • SASM  (if equipped)
  • No power to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • Data Link Connector (DLC)
  • Scan tool
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.