2011 Ford Mustang Base, 2D Convertible, AutomaticFACTORY OEM SERVICE PROCEDURE

DTC Chart

NOTE: Some modules on this vehicle utilize a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground.

Continuous Memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.

DTC CHART

DTC Description Source Action
B2477
  • Module Configuration Failure
  • Front Display Interface Module (FDIM)
  • Smart Junction Box (SJB)
P0315 Crankshaft Position System Variation Not Learned
  • PCM
 Using the scan tool, Carry out the Misfire Monitor Neutral Profile Correction procedure, following the on-screen instructions.
P0602 Powertrain Control Module Programming Error
  • PCM
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
P0605 Internal Control Module Read Only Memory (ROM  ) Error
  • PCM
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
P1639 Vehicle ID Block Corrupted, Not Programmed
  • PCM
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U0300 Internal Control Module Software Incompatibility
  • PCM
  • Restraints Control Module (RCM)
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U201A:51 Control Module Main Calibration Data: Not Programmed
  • Audio Control Module (ACM)
  • Front Controls Interface Module (FCIM)
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U2050 No Application Present
  • ABS module
  • FDIM 
  • Occupant Classification System Module (OCSM)
  • SJB 
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U2051 One or More Calibration Files Missing/Corrupt
  • ABS module
  • FDIM 
  • OCSM 
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U2100:00 Initial Configuration Not Complete: No Sub Type Information
  • ACM 
  • Power Steering Control Module (PSCM)
  • RCM 
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U2100:00 Initial Configuration Not Complete: No Sub Type Information
  • Accessory Protocol Interface Module (APIM)
 Carry out APIM  programming. Refer to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING  in this service information.
U2100:55 Initial Configuration Not Complete: Not Configured
  • Body Control Module B (BCM-B)
  • Instrument Panel Cluster (IPC)
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U2101:00 Control Module Configuration Incompatible: No Sub Type Information
  • APIM 
 Carry out APIM  programming. Refer to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING  in this service information.
U2101:00 Control Module Configuration Incompatible: No Sub Type Information * ACM  Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U2101:56 Control Module Configuration Incompatible: Invalid/Incompatible Configuration
  • IPC 
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
U3002:62 Vehicle Identification Number: Signal Compare Failure
  • RCM 
 Carry out PMI  . Refer to PROGRAMMABLE MODULE INSTALLATION (PMI)  in this service information.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.