Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Ford Explorer Base, FWD, 6F55FACTORY OEM SERVICE PROCEDURE
Exploded View
ITEM DESCRIPTION CHART
| Item | Service Part Number | Description | Tool Number | Material Name | Notes |
|---|---|---|---|---|---|
| 1 | W714133 | Left Hand (LH) catalytic converter manifold heat shield bolt (3 required) | - | - | 12 Nm (106 lb-in) |
| 2 | 9Y427 | Left Hand (LH) catalytic converter manifold heat shield | - | - | - |
| 3 | W712244 | Left Hand (LH) catalytic converter manifold-to-cylinder head stud (6 required) | - | - | 12 Nm (106 lb-in) |
| 4 | 9448 | Gasket | - | - | - |
| 5 | - | Left Hand (LH) Heated Oxygen Sensor (HO2S) electrical connector (part of 9F472) | - | - | - |
| 6 | - | Left Hand (LH) Catalyst Monitor Sensor (CMS) electrical connector (part of 9G444) | - | - | - |
| 7 | 5G232 | Left Hand (LH) catalytic converter manifold | - | - | - |
| 8 | W701706 | Left Hand (LH) catalytic converter manifold-to-cylinder head nut (6 required) | - | - | 25 Nm (18 lb-ft) |
| 9 | 9450 | Gasket | - | - | - |
| 10 | W714265 | Exhaust Y-pipe-to-Left Hand (LH) catalytic converter manifold nut (2 required) | - | - | - |
| 11 | 5G274 | Exhaust Y-pipe | - | - | - |
| 12 | 5230 | Muffler and tailpipe assembly | - | - | - |
ITEM DESCRIPTION CHART
| Item | Service Part Number | Description | Tool Number | Material Name | Notes |
|---|---|---|---|---|---|
| 1 | - | Right Hand (RH) Catalyst Monitor Sensor (CMS) electrical connector (part of 9G444) | - | - | - |
| 2 | W714265 | Right Hand (RH) catalytic converter-to-exhaust manifold nut (4 required) | - | - | - |
| 3 | 5F263 | Gasket | - | - | - |
| 4 | 5E212 | Right Hand (RH) catalytic converter | - | - | - |
| 5 | W712458 | Right Hand (RH) catalytic converter-to-exhaust manifold stud (4 required) | - | - | 25 Nm (18 lb-ft) |
| 6 | W714265 | Exhaust Y-pipe-to-Right Hand (RH) catalytic converter nut (2 required) | - | - | - |
| 7 | 5F262 | Exhaust Y-pipe isolator | - | - | - |
| 8 | 5221 | Torca® clamp | - | - | 55 Nm (41 lb-ft) |
| 9 | 5F262 | Muffler and tailpipe assembly exhaust isolator (4 required) | - | - | - |
Refer to the procedures and/or exploded views in this service information for any Warnings, Notices, Notes, Materials, Specifications, and Special Tools. Items in the exploded views may not be listed in order of removal.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
