Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Ford Escape Base, 2.5 7, AWD, StandardFACTORY OEM SERVICE PROCEDURE
Communication Network
COMMUNICATION NETWORK DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Action |
|---|---|---|---|
| U0001 | High Speed CANÂ Communication Bus | ABS module | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0001:88 | High Speed CANÂ Communication Bus: Bus Off | ABS module | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failures | Restraints Control Module (RCM) | The RCM is not receiving Roll Stability Control (RSC®) messages from the ABS module. CLEAR the DTC. REPEAT the network test with the scan tool. If the ABS module does not pass the network test, GO to PINPOINT TEST B . |
| U0028:88 | Vehicle Communication Bus A: Bus Off | RCMÂ | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0100 | Lost Communication with ECMÂ /PCM | 4X4 control module ABS module Battery Control Module - High Voltage Traction Battery (BCMHVTB) Instrument Cluster (IC) Power Steering Control Module (PSCM) TCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST A . |
| U0100:00 | Lost Communication With ECMÂ /PCM "A": No Sub Type Information | ABS module (hybrid) Accessory Protocol Interface Module (APIM) Air Conditioning Compressor Module (ACCM) RCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST A . |
| U0101 | Lost Communication with TCMÂ | Battery Control Module - High Voltage Traction Battery (BCMHVTB) (hybrid) ICÂ (hybrid) PCM (hybrid) PSCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST H . |
| U0111 | Lost Communication with Battery Energy Control Module | ICÂ
(hybrid) PCM (hybrid) TCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST I . |
| U0114 | Lost Communication With Four-Wheel Drive Clutch Control Module | ABS module ICÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST D . |
| U0114:00 | Lost Communication With Four-Wheel Drive Clutch Control Module: No Sub Type Information | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST D . |
| U0121 | Lost Communication with Anti-Lock Brake System (ABS) Control Module | 4X4 control module ICÂ PSCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST B . |
| U0129 | Lost Communication with Brake System Control Module | ICÂ
(hybrid) PCM TCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST B . |
| U0131 | Lost Communication With Power Steering Control Module (PSCM) | ICÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST G . |
| U0131:87 | Lost Communication With Power Steering Control Module (PSCM): Missing Message | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST G . |
| U0140 | Lost Communication with Body Control Module (GEMÂ ) | Audio Control Module (ACM) Front Controls Interface Module (FCIM) Front Display Interface Module (FDIM) HVAC module ICÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST Q . |
| U0140:00 | Lost Communication with Body Control Module: No Sub Type Information |
|
|
| U0151 | Lost Communication with Restraints Control Module | ABS module ICÂ Occupant Classification System Module (OCSM) |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST E . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | APIMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST E . |
| U0151:87 | Lost Communication with Restraints Control Module: Missing Message | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST E . |
| U0151:88 | Lost Communication with Restraints Control Module: Bus Off | ABS module | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0154:00 | Lost Communication with Restraints Occupant Classification System Module: No Sub Type Information | RCMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST F . |
| U0155 | Lost Communication with Instrument Panel Cluster (ICÂ ) Control Module | 4X4 control module ABS module ACMÂ BCM-HVTBÂ FDIMÂ HVAC module PSCMÂ Smart Junction Box (SJB) |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST C . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPCÂ ) Control Module: No Sub Type Information | ACCMÂ ACMÂ APIMÂ GPSMÂ RCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST C . |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPCÂ ) Control Module: Missing Message | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST C . |
| U0159 | Lost Communication with Parking Assist Control Module (PAMÂ ) | ACMÂ ICÂ PSCMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST J . |
| U0159:00 | Lost Communication with Parking Assist Control Module "A": No Sub Type Information | ACMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST J . |
| U0162:00 | Lost Communication with Navigation Display Module: No Sub Type Information | ACMÂ | REFER to DRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM article. |
| U0163 | Lost Communication With Navigation Control Module (NAV) | ICÂ | REFER to DRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM article. |
| U0164 | Lost Communication With HVAC Control Module (EATCÂ ) | FDIMÂ ICÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST L . |
| U0164:00 | Lost Communication with HVAC Control Module: No Sub Type Information | ACMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST L . |
| U016A:00 | Lost Communication with Global Positioning System Module: No Sub Type Information | APIMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST M . |
| U0184 | Lost Communication with Radio (ACMÂ ) | FCIMÂ FDIMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST P . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | APIMÂ FCIMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST P . |
| U0197 | Lost Communication with Telephone Control Module | ACMÂ FDIMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST R . |
| U0197:00 | Lost Communication with Telephone Control Module: No Sub Type Information | ACMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST R . |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | RCMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST R . |
| U0255 | Lost Communication with Front Controls Interface Module | ACMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST O . |
| U0255:00 | Lost Communication with Front Display Interface Module: No Sub Type Information | ACMÂ APIMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST N . |
| U0256 | Lost Communication with Front Display Interface Module | ACMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST N . |
| U0256:00 | Lost Communication with Front Controls Interface Module "A": No Sub Type Information | ACMÂ APIMÂ |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST O . |
| U0294 | Lost Communication With Powertrain Control Module | TCMÂ | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, GO to PINPOINT TEST A . |
| U0298:87 | Lost Communication With DC to DC Converter Control Module "A": Missing Message | ABS module | REFER to HIGH VOLTAGE CONVERTER/INVERTER article. |
| U0401 | Invalid Data Received from ECMÂ /PCM A | 4X4 control module ABS module BCM-HVTBÂ |
RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0402 | Invalid Data Received from TCMÂ | BCM-HVTBÂ | RETRIEVE and FOLLOW non-network DTCs from the TCMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0401:00 | Invalid Data Received from ECMÂ /PCM: No Sub Type Information | ABS module RCMÂ |
RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0401:68 | Invalid Data Received from ECMÂ /PCM: Event information | ACCMÂ | RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0402 | Invalid Data Received from TCMÂ | ABS module | RETRIEVE and FOLLOW non-network DTCs from the TCMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0414 | Invalid Data Received from Four-Wheel Drive Clutch Control Module | ABS module | RETRIEVE and FOLLOW non-network DTCs from the 4X4 control module. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0415 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module | 4X4 control module PSCMÂ |
RETRIEVE and FOLLOW non-network DTCs from the ABS module. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0420:87 | Invalid Data Received From Power Steering Control Module: Missing Message | ABS module | RETRIEVE and FOLLOW non-network DTCs from the Power Steering Control Module (PSCM). REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | APIMÂ GPSMÂ |
RETRIEVE and FOLLOW non-network DTCs from the SJBÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0422:68 | Invalid Data Received From Body Control Module: Event Information | HVAC module | RETRIEVE and FOLLOW non-network DTCs from the SJBÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0423 | Invalid Data Received From Instrument Panel Cluster (IPCÂ ) Control Module | BCM-HVTBÂ | RETRIEVE and FOLLOW non-network DTCs from the ICÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster (IPCÂ ) Control Module: No Sub Type Information | APIMÂ RCMÂ GPSMÂ |
RETRIEVE and FOLLOW non-network DTCs from the IPCÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0424 | Invalid Data Received HVAC Control Module | BCM-HVTBÂ | RETRIEVE and FOLLOW non-network DTCs from the HVAC module. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0423:64 | Invalid Data Received from Instrument Panel Control Module: Signal Plausibility Failure | ABS module | RETRIEVE and FOLLOW non-network DTCs from the ICÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0423:68 | Invalid Data Received from Instrument Panel Control Module: Event Information | ACCMÂ HVAC module |
RETRIEVE and FOLLOW non-network DTCs from the ICÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0452 | Invalid Data Received from Restraints Control Module | ABS module | RETRIEVE and FOLLOW non-network DTCs from the RCMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0452:29 | Invalid Data Received from Restraints Control Module: Signal Invalid | ABS module | RETRIEVE and FOLLOW non-network DTCs from the RCMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U045A | Invalid Data Received from PAM | PSCMÂ | RETRIEVE and FOLLOW non-network DTCs from the PAMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U046B:00 | Invalid Data Received from Global Positioning System Module: No Sub Type Information | ABS module | RETRIEVE and FOLLOW non-network DTCs from the GPSMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | APIMÂ | RETRIEVE and FOLLOW non-network DTCs from the ACMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module | RCMÂ | RETRIEVE and FOLLOW non-network DTCs from the APIMÂ . REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U1900 | CANÂ Communication Bus Fault - Receive Error | RCMÂ | FOLLOW the pinpoint test for the module which failed the network test. GO to SYMPTOM CHART . |
| U2013 | Compass Module is Not Responding | ICÂ | REFER to ELECTRONIC COMPASS article. |
| U2023 | Fault Received From External Node | ICÂ PSCMÂ |
U2023 is set when a module receives invalid network data from another module with a faulted input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2196 | Invalid 'Engine RPM' Data | ICÂ | RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2197 | Invalid 'Vehicle Speed' Data | ICÂ | RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2198 | Invalid 'Fuel Pulse' Data | ICÂ | RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2199 | Invalid 'Engine Coolant Temperature' Data | ICÂ | RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2200 | Invalid 'ODO Count' Data | ICÂ | RETRIEVE and FOLLOW non-network DTCs from the PCM. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2472 | Unexpected Ignition State | ICÂ SJBÂ |
RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE article for a list of all DTCs. |
| U2473 | Unexpected Vehicle Speed | ACMÂ | REFER to DRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM article. |
| U2473 | Unexpected Vehicle Speed | SJBÂ | REFER to MULTIFUNCTION ELECTRONIC MODULE article. |
| U2510 | CANÂ - Invalid Data for Vehicle Security | ICÂ | REFER to ANTI-THEFT SYSTEM - ANTI-THEFT PERIMETER article (Non-Hybrid) or ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) - HYBRID article (Hybrid). |
| U2511 | CANÂ - Data Mis-Match (Receive Data Does Not Match Expected) | ICÂ | REFER to ANTI-THEFT SYSTEM - ANTI-THEFT PERIMETER article (Non-Hybrid) or ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) - HYBRID article (Hybrid). |
| U261A | CANÂ Data/Configuration Setup Mismatch | ICÂ | REFER to EXTERIOR LIGHTING SYSTEM article. |
| U3000:88 | Control Module: Bus Off | APIMÂ | The module could not communicate on the network at a point in time. The fault is currently not present since the module is currently communicating with the scan tool reporting this DTC. CLEAR the DTC. REPEAT the network test with the scan tool. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
