Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2010TAURUS SEL, FWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXMODULE COMMUNICATIONS NETWORK DTCS
2010 Ford Taurus SEL, FWD
Module Communications Network DTCS
2010 Ford Taurus SEL, FWDSECTION Module Communications Network DTCS
COMMUNICATION NETWORK DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Action |
|---|---|---|---|
| U0001:88 | High Speed CAN Communication Bus: Bus Off | Cruise-Control Module (C-CM) Power Steering Control Module (PSCM) | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0002:88 | High Speed CAN Communication Bus Performance: Bus Off | Instrument Panel Cluster (IPC) | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0011:88 | Medium Speed CAN Communication Bus Performance: Bus Off | IPC | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failures | Restraints Control Module (RCM) | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0028:88 | Vehicle Communication Bus A: Bus Off | RCM | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0073 | Control Module Communication Bus A Off | ABS module | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0074 | Control Module Communication Bus B Off | ABS module | REFER to VEHICLE DYNAMIC SYSTEMS . |
| U0100 | Lost Communication With ECM /PCM | 4X4 control module ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST A: THE PCM DOES NOT RESPOND TO THE SCAN TOOL . |
| U0100:00 | Lost Communication With ECM /PCM "A": No Sub Type Information | Accessory Protocol Interface Module (APIM) C-CM IPC Occupant Classification System Module (OCSM) Power Steering Control Module (PSCM) RCM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST A: THE PCM DOES NOT RESPOND TO THE SCAN TOOL . |
| U0100:87 | Lost Communication With ECM /PCM "A": Missing Message | Remote Function Actuator (RFA) module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST A: THE PCM DOES NOT RESPOND TO THE SCAN TOOL . |
| U0102 | Lost Communication With Transfer Case Control Module (4X4CM) | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST H: THE 4X4 CONTROL MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0102:00 | Lost Communication With Transfer Case Control Module: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST H: THE 4X4 CONTROL MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | Head Up Display (HUD) module IPC ABS module RCM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST I: THE CRUISE-CONTROL MODULE (C-CM) DOES NOT COMMUNICATE WITH THE SCAN TOOL . |
| U0121 | Lost Communication With Anti-Lock Brake System (ABS) Control Module | 4X4 control module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST B: THE ABS MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | APIM C-CM IPC PSCM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST B: THE ABS MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0131 | Lost Communication With Power Steering Control Module (PSCM ) | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST D: THE POWER STEERING CONTROL MODULE (PSCM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST D: THE POWER STEERING CONTROL MODULE (PSCM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0140 | Lost Communication With Body Control Module (GEM ) | Audio Control Module (ACM) Driver Door Module (DDM) Driver Seat Module (DSM) Front Controls Interface Module (FCIM) Front Display Interface Module (FDIM) Interior Lighting Control Module (ILCM) |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST U: THE SMART JUNCTION BOX (SJB) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | ACM APIM Audio Digital Signal Processing (DSP) module FCIM Global Positioning System Module (GPSM) HVAC module IPC |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST U: THE SMART JUNCTION BOX (SJB) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0140:87 | Lost Communication With Body Control Module): Missing Message | RFA
module HVAC module |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST U: THE SMART JUNCTION BOX (SJB) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0151 | Lost Communication With Restraints Control Module | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST E: THE RESTRAINTS CONTROL MODULE (RCM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | APIM IPC OCSM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST E: THE RESTRAINTS CONTROL MODULE (RCM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0154:00 | Lost Communication With Restraints Occupant Classification System Module: No Sub Type Information | IPC RCM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST F: THE OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) DOES NOT COMMUNICATE WITH THE SCAN TOOL . |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC ) Module | 4X4 control module ABS module ACM DSM FDIM GPSM Smart Junction Box (SJB) |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST C: THE INSTRUMENT PANEL CLUSTER (IPC) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC ) Control Module: No Sub Type Information | ACM APIM Audio DSP module C-CM HUD module HVAC module RCM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST C: THE INSTRUMENT PANEL CLUSTER (IPC) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC ) Control Module: Missing Message | RFA
module HVAC module |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST C: THE INSTRUMENT PANEL CLUSTER (IPC) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0158:00 | Lost Communication With Head Up Display: No Sub Type Information | C-CM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST G: THE HEAD UP DISPLAY (HUD) MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0159 | Lost Communication With Parking Assist Control Module (PAM ) | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST J: THE PARKING AID MODULE (PAM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | ACM IPC PSCM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST J: THE PARKING AID MODULE (PAM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0161:00 | Lost Communication With Compass Module: No Sub Type Information | IPC | REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | ACM | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS . |
| U0163:00 | Lost Communication With Navigation Control Module: No Sub Type Information | HVAC module IPC |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST N: THE FRONT CONTROLS INTERFACE MODULE (FCIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0164 | Lost Communication With HVAC Control Module (EATC ) | FCIM FDIM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST V: THE HVAC MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST V: THE HVAC MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | APIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST P: THE GLOBAL POSITIONING SYSTEM MODULE (GPSM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0184 | Lost Communication With Radio (ACM ) | FCIM FDIM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST M: THE AUDIO CONTROL MODULE (ACM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | APIM Audio DSP module FCIM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST M: THE AUDIO CONTROL MODULE (ACM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0197 | Lost Communication With Telephone Control Module | ACM FDIM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST L: THE ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | ACM Audio DSP module |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST L: THE ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST T: THE DRIVER SEAT MODULE (DSM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0214:00 | Lost Communication With Remote Function Actuator: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST K: THE REMOTE FUNCTION ACTUATOR (RFA) MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST R: THE SIDE OBSTACLE DETECTION CONTROL MODULE - LEFT (SOD-L) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST S: THE SIDE OBSTACLE DETECTION CONTROL MODULE - RIGHT (SOD-R) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0238 | Lost Communication With Digital Audio Control Module "D" (DSP ) | FDIM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST W: THE AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST W: THE AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE DOES NOT RESPOND TO THE SCAN TOOL . |
| U0242:00 | Lost Communication With Headlamp Control Module "B": No Sub Type Information | IPC | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST Y: THE HEADLAMP CONTROL MODULE 2 (HCM-2) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | RCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST L: THE ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0255 | Lost Communication With Front Controls Interface Module | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST N: THE FRONT CONTROLS INTERFACE MODULE (FCIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | ACM APIM |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST O: THE FRONT DISPLAY INTERFACE MODULE (FDIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0256 | Lost Communication With Front Display Interface Module | ACM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST O: THE FRONT DISPLAY INTERFACE MODULE (FDIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | ACM APIM HVAC module |
CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, Go To PINPOINT TEST N: THE FRONT CONTROLS INTERFACE MODULE (FCIM) DOES NOT RESPOND TO THE SCAN TOOL . |
| U0401 | Invalid Data Received from ECM /PCM A | 4X4 control module | RETRIEVE and FOLLOW the DTCs from the PCM. |
| U0401:00 | Invalid Data Received from ECM /PCM A: No Sub Type Information | OCSM PSCM RCM |
RETRIEVE and FOLLOW the DTCs from the PCM. |
| U0401:68 | Invalid Data Received from ECM /PCM A: Event Information | C-CM IPC |
RETRIEVE and FOLLOW the DTCs from the PCM. |
| U0405 | Invalid Data Received from Cruise Control Module | ABS module | RETRIEVE and FOLLOW the DTCs from the C-CM . |
| U0405:55 | Invalid Data Received from Cruise Control Module: Not Configured | IPC | RETRIEVE and FOLLOW the DTCs from the C-CM . |
| U0405:68 | Invalid Data Received from Cruise Control Module: Event Information | HUD module | RETRIEVE and FOLLOW the DTCs from the C-CM . |
| U0415 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module | 4X4 control module | RETRIEVE and FOLLOW the DTCs from the ABS module. |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | PSCM | RETRIEVE and FOLLOW the DTCs from the ABS module. |
| U0418:68 | Invalid Data Received from Brake System Control Module: Event Information | C-CM | RETRIEVE and FOLLOW the DTCs from the ABS module. |
| U0420 | Invalid Data Received From Power Steering Control Module | ABS module | RETRIEVE and FOLLOW the DTCs from the PSCM . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | APIM GPSM |
RETRIEVE and FOLLOW the DTCs from the SJB . |
| U0422:55 | Invalid Data Received From Body Control Module: Not Configured | IPC | RETRIEVE and FOLLOW the DTCs from the SJB . |
| U0422:68 | Invalid Data Received From Body Control Module: Event Information | HVAC module | RETRIEVE and FOLLOW the DTCs from the SJB . |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | APIM GPSM |
RETRIEVE and FOLLOW the DTCs from the IPC . |
| U0423:68 | Invalid Data Received From Instrument Panel Cluster Control Module: Event Information | HUD
module HVAC module RFA module |
RETRIEVE and FOLLOW the DTCs from the IPC . |
| U0424:68 | Invalid Data Received From HVAC Control Module: Event Information | C-CM | RETRIEVE and FOLLOW the DTCs from the HVAC module. |
| U0430:68 | Invalid Data Received From Tire Pressure Monitor Module: Event Information | IPC | RETRIEVE and FOLLOW the DTCs from the SJB . |
| U0452 | Invalid Data Received from Restraints Control Module | ABS module | RETRIEVE and FOLLOW the DTCs from the RCM . |
| U0459:68 | Invalid Data Received from Head Up Display: Event Information | C-CM | RETRIEVE and FOLLOW the DTCs from the HUD module. |
| U045A:00 | Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information | PSCM | RETRIEVE and FOLLOW the DTCs from the PAM . |
| U045A:55 | Invalid Data Received From Parking Assist Control Module "A": Not Configured | IPC | RETRIEVE and FOLLOW the DTCs from the PAM . |
| U045A:68 | Invalid Data Received From Parking Assist Control Module "A": Event Information | IPC | RETRIEVE and FOLLOW the DTCs from the PAM . |
| U0462:68 | Invalid Data Received From Compass Module: Event Information | IPC | REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES . |
| U0464:68 | Invalid Data Received From Navigation Control Module: Event Information | HVAC module | RETRIEVE and FOLLOW the DTCs from the ACM . |
| U046B:00 | Invalid Data Received From Global Positioning System Module: No Sub Type Information | APIM | RETRIEVE and FOLLOW the DTCs from the GPSM . |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | APIM | RETRIEVE and FOLLOW the DTCs from the ACM . |
| U049A:68 | Invalid Data Received from "Door Control Module A": Event Information | RFA module | RETRIEVE and FOLLOW the DTCs from the DDM . |
| U0515:56 | Invalid Data Received from RFA Module | IPC | IPC RETRIEVE and FOLLOW the DTCs from the RFA module. |
| U0554:00 | Invalid Data Received from Accessory Protocol Interface Module: No Sub Type Information | RCM | RETRIEVE and FOLLOW the DTCs from the APIM . |
| U0557:68 | Invalid Data Received From Front Controls Interface Module "A": Event Information | HVAC module | RETRIEVE and FOLLOW the DTCs from the FCIM . |
| U2023 | Fault Received From External Node | ABS module | The module had an invalid network input/message from another module. RETRIEVE and FOLLOW the non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U2472 | Unexpected Ignition State | SJB | REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U2473 | Unexpected Vehicle Speed (VSS ) | SJB | REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U3000:88 | Control Module: Bus Off | APIM | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.