Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2010 Ford Focus SEL, StandardFACTORY OEM SERVICE PROCEDURE
Restraints Control Module (RCM) DTC Chart
Restraints Control Module (RCM) DTC Chart
| DTC | Description | Action To Take |
|---|---|---|
| Continuous lamp | The Air Bag Warning Indicator is Illuminated Continuously | GO to PINPOINT TEST A . |
| B1231 | Event Threshold Exceeded | INSTALL a new Restraints Control Module (RCM). REFER to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT . |
| B1317 | Battery Voltage High | GO to PINPOINT TEST Y . |
| B1318 | Battery Voltage Low | GO to PINPOINT TEST Y . |
| B1342 | ECU Is Faulted | INSTALL a new RCMÂ . REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| B1868 | Lamp Air Bag Warning Indicator Circuit Failure | GO to PINPOINT TEST B . |
| B1884 | PADÂ Warning Lamp Circuit Failure | GO to PINPOINT TEST C . |
| B1890 | PADÂ Warning Lamp Circuit Short to Battery | GO to PINPOINT TEST D . |
| B2290 | Occupant Classification System Fault |
NOTE:
If no DTCs are present in the Occupant Classification System Module (OCSM) and DTC B2290 is only present in the RCMÂ
as a continuous DTC, CLEAR all RCMÂ
DTCs and PROVE OUT the system. The OCSMÂ
reported a fault message to the RCMÂ
. CARRY OUT self-test of the OCSMÂ
and RETRIEVE continuous DTCs. |
| B2292 | Restraint System - Seatbelt Pretensioner Fault | GO to PINPOINT TEST F . |
| B2293 | Restraint System - Air Bag Fault | GO to PINPOINT TEST G . |
| B2294 | Restraint System - Curtain Fault | GO to PINPOINT TEST H . |
| B2295 | Restraint System - Side Air Bag Fault | GO to PINPOINT TEST I . |
| B2296 | Restraint System - Impact Sensor Fault | GO to PINPOINT TEST J . |
| B2432 | Drivers Seat Belt Buckle Switch Circuit Open | GO to PINPOINT TEST K . |
| B2433 | Drivers Seat Belt Buckle Switch Circuit Short to Battery | GO to PINPOINT TEST L . |
| B2434 | Drivers Seat Belt Buckle Switch Circuit Short To Ground | GO to PINPOINT TEST M . |
| B2435 | Drivers Seat Belt Buckle Switch Resistance out of Range | GO to PINPOINT TEST N . |
| B2436 | Passengers Seat Belt Buckle Switch Circuit Open | GO to PINPOINT TEST O . |
| B2437 | Passengers Seat Belt Buckle Switch Circuit Short to Battery | GO to PINPOINT TEST P . |
| B2438 | Passengers Seat Belt Buckle Switch Short to Ground | GO to PINPOINT TEST Q . |
| B2439 | Passengers Seat Belt Buckle Switch Resistance Out of Range | GO to PINPOINT TEST R . |
| B2477 | Module Configuration Failure |
NOTE:
When installing a new RCMÂ
, always make sure the correct RCMÂ
is being installed. If an incorrect RCMÂ
is installed, erroneous DTCs will result. INSTALL a new RCMÂ
. REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B2607 | Harness/Configuration Mismatch |
NOTE:
When installing a new RCMÂ
, always make sure the correct RCMÂ
is being installed. If an incorrect RCMÂ
is installed, erroneous DTCs will result. INSTALL a new RCMÂ
. REFER to RESTRAINTS CONTROL MODULE (RCM)
. |
| B2792 | Cross Link Between Loops | Firing GO to PINPOINT TEST S . |
| C1414 | Incorrect Module Design Level | INSTALL a new RCMÂ . REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| C1946 | Front Driver's Seat Track Position Switch Circuit Open | GO to PINPOINT TEST U . |
| C1947 | Front Driver's Seat Track Position Switch Circuit Short to Ground | GO to PINPOINT TEST V . |
| C1948 | Front Driver's Seat Track Position Switch Circuit Resistance Out of Range | GO to PINPOINT TEST W . |
| C1982 | Front Driver's Seat Track Position Switch Circuit Short to Battery | GO to PINPOINT TEST X . |
| U0100 | Lost Communication With ECM/PCM | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the communication concern. |
| U0154 | Lost Communication With Restraints Occupant Classification System Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the communication concern. |
| U0253 | Lost Communication With Accessory Protocol Interface Module |
NOTE:
This DTC will set in the RCMÂ
if a message is not received from the APIMÂ
. Check for additional RCMÂ
and APIMÂ
DTCs.REFER to the appropriate section to diagnose DTCs concern. If no other DTCs are present, REFER to APIM SOFTWARE LEVEL CHECK
. |
| U0401 | Invalid Data Received From ECM/PCM A | RETRIEVE PCM DTCs. If DTCs are present in the PCM, REFER to INTRODUCTION - GASOLINE MODELS to diagnose the concern. If DTCs are not present in the PCM and DTC U0401 is present in the RCMÂ as a on-demand DTC, INSTALL a new RCMÂ . REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U0455 | Invalid Data Received From Restraints Occupant Classification System Module | REPAIR all on-demand Occupant Classification Sensor (OCS) system DTCs, CLEAR all RCMÂ
DTCs and PROVE OUT the system. If no DTCs are present in the OCSMÂ and DTC U0455 is only present in the RCMÂ continuous, CLEAR all RCMÂ DTCs and PROVE OUT the system. If no DTCs are present in the OCSMÂ and DTC U0455 is present on-demand in the RCMÂ , INSTALL a new OCSÂ service kit. REFER to OCCUPANT CLASSIFICATION SENSOR . |
| U2050 | No Application Present | INSTALL a new RCMÂ . REFER to RESTRAINTS CONTROL MODULE (RCM) . |
| U2051 | One or More Calibration Files Missing/Corrupt | INSTALL a new RCMÂ . REFER to RESTRAINTS CONTROL MODULE (RCM) . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
