Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Ford Focus S, AutomaticFACTORY OEM SERVICE PROCEDURE
Starting System DTCS
PCM DIAGNOSTIC TROUBLE CODES (DTC) LIST
| DTC | Description | Source | Action |
|---|---|---|---|
| P0512 | Starter Request Circuit - Circuit has Power With the Ignition in the OFF Position | PCM | CARRY OUT the Ignition Switch Component Test. Refer to appropriate COMPONENT TESTING article. If necessary, INSTALL a new ignition switch. If the ignition switch passed the component test, REPAIR circuit CDC35 (BU/WH) for a short to power. |
| P0705 | TR Sensor Circuit Failure | PCM | Refer to the appropriate Automatic Transmission article for the procedure. |
| P1702 | TR Sensor Circuit Failure | PCM | Refer to the appropriate Automatic Transmission article for the procedure. |
| P1705 | TR Sensor Circuit Failure | PCM | Refer to the appropriate Automatic Transmission article for the procedure. |
| P0830 | Clutch Pedal Switch A Circuit | PCM | REFER to INTRODUCTION - GASOLINE MODELS article. |
| P0833 | Clutch Pedal Switch B Circuit | PCM | REFER to INTRODUCTION - GASOLINE MODELS article. |
PASSIVE ANTI-THEFT SYSTEM (PATS) DIAGNOSTIC TROUBLE CODES (DTC) LIST
| DTC | Description | Source | Action |
|---|---|---|---|
| B1213 | Anti-Theft Number of Programmed Keys is Below Minimum | PCM | REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
| B1232 | Transceiver Failure | PCM | REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
| B1342 | ECU is faulted | PCM | INSTALL a PCM. REFER to ELECTRONIC ENGINE CONTROLS article. |
| B1600 | Passive Anti-Theft System (PATS) Key Transponder Signal is Not Received | PCM | REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
| B1601 | PATS Received Incorrect Key-Code From Ignition Key Transponder | PCM | REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
| B1602 | PATS Received Invalid Format of Key-Code From Ignition Key Transponder | PCM | REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
| B1681 | PATS Transceiver Module Signal is Not Received | PCM | REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
| B2103 | Antenna Not Connected | PCM | REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
| B2431 | Transponder Programming Failed | PCM | VERIFY if the correct PATS key is being used. If the PATS key is defective, use a new key for programming. REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET article. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.