Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Ford Fusion AWD L4-2.3LFACTORY OEM SERVICE PROCEDURE
Transmission Position Sensor/Switch: Adjustments
Transmission Range (TR) Sensor Adjustment
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Maintenance/Service and Repair.
2. Disconnect the transmission range (TR) sensor electrical connector and the selector lever cable end.
3. NOTE: Failure to hold the selector lever, while loosening or tightening the manual control lever, will transmit rotational torque to the TR switch causing internal damage.
Loosen the TR sensor (the automatic transaxle is shown removed for clarity).
1 Remove the nut and the manual control lever.
2 Loosen the TR sensor bolts.
4. Using the special tool, align the TR sensor and tighten the bolts.
^ Tighten to 10 Nm (89 lb-in).
5. CAUTION: Do not use air tools on this nut. Hold the manual control lever while tightening the manual control lever nut, or damage to the manual control lever shaft or the TR sensor could occur.
Install the manual control lever.
^ Tighten to 22 Nm (16 lb-ft).
6. CAUTION: Check to make sure the manual control lever is in position "2" (same as "D" position). Adjust the manual control lever to TR sensor D position.
1 L (LOW)
2 D (DRIVE)
3 N(NEUTRAL)
4 R (REVERSE)
5 P (PARK)
^ When in position D, the marks on the manual control lever line up with the marks on the TR sensor.
7. Connect the selector lever cable and the TR sensor electrical connector.
Special Tool(s):
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Maintenance/Service and Repair.
2. Disconnect the transmission range (TR) sensor electrical connector and the selector lever cable end.
3. NOTE: Failure to hold the selector lever, while loosening or tightening the manual control lever, will transmit rotational torque to the TR switch causing internal damage.
Loosen the TR sensor (the automatic transaxle is shown removed for clarity).
1 Remove the nut and the manual control lever.
2 Loosen the TR sensor bolts.
4. Using the special tool, align the TR sensor and tighten the bolts.
^ Tighten to 10 Nm (89 lb-in).
5. CAUTION: Do not use air tools on this nut. Hold the manual control lever while tightening the manual control lever nut, or damage to the manual control lever shaft or the TR sensor could occur.
Install the manual control lever.
^ Tighten to 22 Nm (16 lb-ft).
6. CAUTION: Check to make sure the manual control lever is in position "2" (same as "D" position). Adjust the manual control lever to TR sensor D position.
1 L (LOW)
2 D (DRIVE)
3 N(NEUTRAL)
4 R (REVERSE)
5 P (PARK)
^ When in position D, the marks on the manual control lever line up with the marks on the TR sensor.
7. Connect the selector lever cable and the TR sensor electrical connector.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.