Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Ford Edge Limited, FWDFACTORY OEM SERVICE PROCEDURE
Abs Module
ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1317 | Battery Voltage High | ABS Module |
NOTE:
Battery voltage above 16 volts will cause DTC B1317 to set. Verify battery and charging system condition prior to diagnosing this DTC. Go to Pinpoint Test A
under PINPOINT TESTS
. |
| B1318 | Battery Voltage Low | ABS Module |
NOTE:
Battery voltage below 10 volts will cause DTC B1318 to set. Verify battery and charging system condition prior to diagnosing this DTC. Go to Pinpoint Test A
under PINPOINT TESTS
. |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | Go to Pinpoint Test B under PINPOINT TESTS . |
| C1096 | ABS Hydraulic Pump Motor Circuit Open | ABS Module | Go to Pinpoint Test B under PINPOINT TESTS . |
| C1145 | Speed Wheel Sensor RF Input Circuit Failure | ABS Module | Go to Pinpoint Test C under PINPOINT TESTS . |
| C1155 | Speed Wheel Sensor LF Input Circuit Failure | ABS Module | Go to Pinpoint Test C under PINPOINT TESTS . |
| C1165 | Speed Wheel Sensor RR Input Circuit Failure | ABS Module | Go to Pinpoint Test C under PINPOINT TESTS . |
| C1175 | Speed Wheel Sensor LR Input Circuit Failure | ABS Module | Go to Pinpoint Test C under PINPOINT TESTS . |
| C1222 | Speed Wheel Mismatch | ABS Module | Go to Pinpoint Test D under PINPOINT TESTS . |
| C1233 | Speed Wheel LF Input Signal Missing | ABS Module | Go to Pinpoint Test D under PINPOINT TESTS . |
| C1234 | Speed Wheel RF Input Signal Missing | ABS Module | Go to Pinpoint Test D under PINPOINT TESTS . |
| C1235 | Speed Wheel RR Input Signal Missing | ABS Module | Go to Pinpoint Test D under PINPOINT TESTS . |
| C1236 | Speed Wheel LR Input Signal Missing | ABS Module | Go to Pinpoint Test D under PINPOINT TESTS . |
| C1278 | Steering Wheel Angle 1 and 2 Signal Faulted | ABS Module | Go to Pinpoint Test E under PINPOINT TESTS . |
| C1279 | Yaw Rate Sensor Circuit Failure | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| C1280 | Yaw Rate Sensor Signal Fault | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| C1281 | Lateral Accelerometer Circuit Failure | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| C1282 | Lateral Accelerometer Signal Fault | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| C1288 | Brake Pressure Transducer Main/Primary Input Circuit Failure | ABS Module | Go to Pinpoint Test G under PINPOINT TESTS . |
| C1446 | Brake Switch Circuit Failure | ABS Module | Go to Pinpoint Test H under PINPOINT TESTS . |
| C1516 | Roll Rate Sensor Signal Fault | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| C1517 | Roll Rate Sensor Circuit Fault | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| C1991 | Module Calibration Failure | ABS Module |
NOTE:
If other DTCs are present, REPAIR them before diagnosing DTC C1991. Go to Pinpoint Test I
under PINPOINT TESTS
. |
| C2769 | Longitudinal Acceleration Sensor Electrical Failure | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| C2770 | Longitudinal Acceleration Sensor Plausibility Failure | ABS Module | Go to Pinpoint Test F under PINPOINT TESTS . |
| U1901 | CAN Network #2 Comm Bus Fault - Receive Error | ABS Module |
NOTE:
If other DTCs are present, REPAIR them before diagnosing DTC U1901. Go to Pinpoint Test J
under PINPOINT TESTS
. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.
