Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Ford Edge AWD V6-3.5LFACTORY OEM SERVICE PROCEDURE
Dual Climate Controlled Seat Module (DCSM)
DUAL CLIMATE CONTROLLED SEAT MODULE (DCSM)
Exploded View











Special Tool(s)

Removal and Installation
NOTE:
- The air bag warning indicator illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
- When installing a new dual climate controlled seat module (DCSM), it is necessary to carry out programmable module installation (PMI).
- The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
1. Before removing the DCSM, carry out the appropriate steps in the PMI procedure.
2. Remove the front passenger seat.
3. Remove the DCSM.
- Disconnect the 3 electrical connectors.
- Remove the 2 screws.
- Remove the DCSM.
4. To install, reverse the removal procedure.
5. Install the front passenger seat. Do not prove out the SRS at this time.
6. Carry out the Occupant Classification Sensor (OCS) System Zero Seat Weight Test.
7. Install the DCSM software data. Carry out the appropriate steps in the PMI procedure.
Exploded View
Front Seat Backrest, Manual and Power Recline, Without Fold Flat (Part 1):
Front Seat Backrest, Manual and Power Recline, Without Fold Flat (Part 2):
Front Seat Backrest, Manual Recline With Fold Flat (Part 1):
Front Seat Backrest, Manual Recline With Fold Flat (Part 2):
Seat Cushion With Power Seat Track (Part 1):
Seat Cushion With Power Seat Track (Part 2):
Driver Seat Cushion With Manual Seat Track (Part 1):
Driver Seat Cushion With Manual Seat Track (Part 2):
Passenger Seat Cushion With Manual Seat Track:
Passenger Power Seat Track (Part 1):
Passenger Power Seat Track (Part 2):
Special Tool(s)
Special Tool(s):
Removal and Installation
NOTE:
- The air bag warning indicator illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
- When installing a new dual climate controlled seat module (DCSM), it is necessary to carry out programmable module installation (PMI).
- The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
1. Before removing the DCSM, carry out the appropriate steps in the PMI procedure.
2. Remove the front passenger seat.
3. Remove the DCSM.
- Disconnect the 3 electrical connectors.
- Remove the 2 screws.
- Remove the DCSM.
4. To install, reverse the removal procedure.
5. Install the front passenger seat. Do not prove out the SRS at this time.
6. Carry out the Occupant Classification Sensor (OCS) System Zero Seat Weight Test.
7. Install the DCSM software data. Carry out the appropriate steps in the PMI procedure.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
