Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Ford Crown Victoria Police InterceptorFACTORY OEM SERVICE PROCEDURE
Vehicle Dynamic Systems DTCS
ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1342 | Electronic Control Unit (ECU) is Defective | ABS Module | INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . |
| B1484 | Brake Pedal Input Open Circuit | ABS Module | Go to Pinpoint Test D . |
| B1596 | Service Continuous Codes | ABS Module |
NOTE:
If other DTCs are present, REPAIR them before installing a new component. TURN the ignition switch to the OFF position and wait at least 30 seconds. TURN the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to ABS MODULE DIAGNOSTIC TROUBLE CODE INDEX. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the Symptom Chart
. |
| B1676 | Battery Voltage Out of Range | ABS Module | Go to Pinpoint Test E . |
| C1145 | Speed Wheel Sensor RF Input Circuit Failure | ABS Module | Go to Pinpoint Test B . |
| C1155 | Speed Wheel Sensor LF Input Circuit Failure | ABS Module | Go to Pinpoint Test B . |
| C1165 | Speed Wheel Sensor RR Input Circuit Failure | ABS Module | Go to Pinpoint Test B . |
| C1175 | Speed Wheel Sensor LR Input Circuit Failure | ABS Module | Go to Pinpoint Test B . |
| C1222 | Speed Wheel Mismatch | ABS Module | MAKE SURE the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. |
| C1266 | ABS Valve Power Relay Circuit Failure | ABS Module | Go to Pinpoint Test H . |
| C1296 | Wheel Speed LF Signal Fault | ABS Module | Go to Pinpoint Test C . |
| C1297 | Wheel Speed RF Signal Fault | ABS Module | Go to Pinpoint Test C . |
| C1298 | Wheel Speed RR Signal Fault | ABS Module | Go to Pinpoint Test C . |
| C1299 | Wheel Speed LR Signal Fault | ABS Module | Go to Pinpoint Test C . |
| C1300 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | Go to Pinpoint Test A . |
| C1805 | Mismatched PCM and ABS Modules Do Not Match | ABS Module | CHECK the part numbers. INSTALL the correct module. |
| C2775 | TC ON/OFF Switch Stuck Failure | ABS Module | Go to Pinpoint Test G . |
| U0073 | Control Module Communication Bus Off | CAN Bus | REFER to MODULE COMMUNICATIONS NETWORK article. |
| U1900 | CAN Communication Bus Fault - Receive Error | CAN Bus | REFER to MODULE COMMUNICATIONS NETWORK article. |
| U2023 | Fault Received From External Node | CAN Bus | REFER to MODULE COMMUNICATIONS NETWORK article. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
