Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Ford Focus L4-2.3L VIN ZFACTORY OEM SERVICE PROCEDURE
Torque Specifications
Cylinder head bolts
NOTE: The cylinder head bolts are torque-to-yield and must not be reused. New cylinder head bolts must be installed.
NOTE: Lubricate the bolts with clean engine oil prior to installation.
Install 10 new cylinder head bolts. Tighten the bolts in the sequence shown in 5 stages.
Stage 1: Tighten to 5 Nm (44 inch lbs.)
Stage 2: Tighten to 15 Nm (11 ft. lbs.)
Stage 3: Tighten to 45 Nm (33 ft. lbs.)
Stage 4: Turn 90°
Stage 5: Turn an additional 90°

Intake manifold bolts 18 Nm (13 ft. lbs.)
NOTE: 2.0L engine shown, 2.3L engine similar.
Inspect and install new intake manifold gaskets if necessary.

2.3L engines
NOTE: Be sure to install the bolts in the previously marked locations.
NOTE: To ease installation of the intake manifold, lower center mounting bolt, use a 6-inch long, 5/16-inch diameter hose.
Install the intake manifold and the 7 mounting bolts.
Tighten to 18 Nm (13 ft. lbs.)

2.0L engines
NOTE: Be sure to install the bolts in the previously marked locations.
Install the intake manifold and the 7 mounting bolts.
Tighten to 18 Nm (13 ft. lbs.)

All engines
Install the lower intake manifold bolt.
Tighten to 18 Nm (13 ft. lbs.)

Camshafts Bearing Caps
NOTE: Lubricate the camshaft journals and bearing caps with clean engine oil.
Install the camshafts and bearing caps. Tighten the bolts in the sequence shown in 3 stages.
Stage 1: Tighten one turn at a time until tight.
Stage 2: Tighten to 7 Nm (62 inch lbs.)
Stage 3: Tighten to 16 Nm (12 ft. lbs.)

Camshaft sprocket bolt 72 Nm (53 ft. lbs.)
Cylinder head temperature (CHT) sensor 12 Nm (9 ft. lbs.)
NOTE: The cylinder head bolts are torque-to-yield and must not be reused. New cylinder head bolts must be installed.
NOTE: Lubricate the bolts with clean engine oil prior to installation.
Install 10 new cylinder head bolts. Tighten the bolts in the sequence shown in 5 stages.
Stage 1: Tighten to 5 Nm (44 inch lbs.)
Stage 2: Tighten to 15 Nm (11 ft. lbs.)
Stage 3: Tighten to 45 Nm (33 ft. lbs.)
Stage 4: Turn 90°
Stage 5: Turn an additional 90°
Intake manifold bolts 18 Nm (13 ft. lbs.)
NOTE: 2.0L engine shown, 2.3L engine similar.
Inspect and install new intake manifold gaskets if necessary.
2.3L engines
NOTE: Be sure to install the bolts in the previously marked locations.
NOTE: To ease installation of the intake manifold, lower center mounting bolt, use a 6-inch long, 5/16-inch diameter hose.
Install the intake manifold and the 7 mounting bolts.
Tighten to 18 Nm (13 ft. lbs.)
2.0L engines
NOTE: Be sure to install the bolts in the previously marked locations.
Install the intake manifold and the 7 mounting bolts.
Tighten to 18 Nm (13 ft. lbs.)
All engines
Install the lower intake manifold bolt.
Tighten to 18 Nm (13 ft. lbs.)
Camshafts Bearing Caps
NOTE: Lubricate the camshaft journals and bearing caps with clean engine oil.
Install the camshafts and bearing caps. Tighten the bolts in the sequence shown in 3 stages.
Stage 1: Tighten one turn at a time until tight.
Stage 2: Tighten to 7 Nm (62 inch lbs.)
Stage 3: Tighten to 16 Nm (12 ft. lbs.)
Camshaft sprocket bolt 72 Nm (53 ft. lbs.)
Cylinder head temperature (CHT) sensor 12 Nm (9 ft. lbs.)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
