Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Ford Expedition 4WDFACTORY OEM SERVICE PROCEDURE
Liftgate/Trunk Module (LTM)
LIFTGATE/TRUNK MODULE (LTM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Perform Test |
|---|---|---|
| B106E | Solid State Driver Disabled Due to Short Circuit | Go to Pinpoint Test A . |
| B107D | Obstacle Detected While Closing | VERIFY obstacle is not present. CLEAR the DTCs. REPEAT the self-test. If DTC B107D returns, go to Pinpoint Test D . |
| B1105 | Rear Open/Close Switch Active During Self-Test | Go to Pinpoint Test B . |
| B1179 | Latch Motor Circuit Short to Battery | Go to Pinpoint Test A . |
| B117A | Latch Motor Circuit Short to Ground | Go to Pinpoint Test A . |
| B117B | Latch Motor Circuit Open | Go to Pinpoint Test A . |
| B117C | Latch Centering Switch Invalid | If any other power liftgate related DTCs are present, DIAGNOSE those first. If no other power liftgate DTCs are present, go to Pinpoint Test I . |
| B2019 | Liftgate Exceeded Time Allowed to Cinch Door | Go to Pinpoint Test C . |
| B236A | Chime Output Circuit Open | Go to Pinpoint Test E . |
| B2418 | Sensor Power Short to Ground | Go to Pinpoint Test A . |
| B2419 | Sensor 1 Invalid | Go to Pinpoint Test A . |
| B2420 | Sensor 2 Invalid | Go to Pinpoint Test A . |
| B2552 | Vbatt 2 Circuit Open | Go to Pinpoint Test A . |
| B2699 | Left Pinch Strip Open or Short to Battery | Go to Pinpoint Test F . |
| B2700 | Right Pinch Strip Open or Short to Battery | Go to Pinpoint Test F . |
| B2701 | Left Pinch Strip Stuck Active | Go to Pinpoint Test G . |
| B2702 | Right Pinch Strip Stuck Active | Go to Pinpoint Test G . |
| B2703 | Open/Close Switch Stuck Active | Go to Pinpoint Test B . |
| B2819 | Gate Motor Circuit Short to Battery | Go to Pinpoint Test A . |
| B2903 | Chime Output Circuit Short to Battery | Go to Pinpoint Test E . |
| B2908 | Latch Switch Invalid | For an inoperative power liftgate, go to Pinpoint Test A . For a power liftgate that stops in secondary latch position, go to Pinpoint Test C . |
| B2935 | Drive Unit Failure | Go to Pinpoint Test A . |
| B2936 | Gate Motor Open | Go to Pinpoint Test A . |
| B2937 | Gate Motor Short to Ground | Go to Pinpoint Test A . |
| B2939 | Gate Clutch Short to Ground or Open | Go to Pinpoint Test A . |
| B2940 | Chime Output Circuit Short to Ground | Go to Pinpoint Test E . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.