2007 Ford Edge SEL Plus, AWDFACTORY OEM SERVICE PROCEDURE

Abs Module

ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC Description Source Perform Test
B1317 Battery Voltage High Anti-lock Brake System (ABS) Module
NOTE: Battery voltage above 16 volts will cause DTC B1317 to set. Verify battery and charging system condition prior to diagnosing this DTC.
Go to Pinpoint Test A .
B1318 Battery Voltage Low ABS Module
NOTE: Battery voltage below 10 volts will cause DTC B1318 to set. Verify battery and charging system condition prior to diagnosing this DTC.
Go to Pinpoint Test A .
C1095 ABS Hydraulic Pump Motor Circuit Failure ABS Module Go to Pinpoint Test B .
C1096 ABS Hydraulic Pump Motor Circuit Open ABS Module Go to Pinpoint Test B .
C1140 Hydraulic Base Brake Failure ABS Module Go to Pinpoint Test H .
C1145 Speed Wheel Sensor RF Input Circuit Failure ABS Module Go to Pinpoint Test C .
C1155 Speed Wheel Sensor LF Input Circuit Failure ABS Module Go to Pinpoint Test C .
C1165 Speed Wheel Sensor RR Input Circuit Failure ABS Module Go to Pinpoint Test C .
C1175 Speed Wheel Sensor LR Input Circuit Failure ABS Module Go to Pinpoint Test C .
C1222 Speed Wheel Mismatch ABS Module Go to Pinpoint Test D .
C1233 Speed Wheel LF Input Signal Missing ABS Module Go to Pinpoint Test D .
C1234 Speed Wheel RF Input Signal Missing ABS Module Go to Pinpoint Test D .
C1235 Speed Wheel RR Input Signal Missing ABS Module Go to Pinpoint Test D .
C1236 Speed Wheel LR Input Signal Missing ABS Module Go to Pinpoint Test D .
C1278 Steering Wheel Angle 1 and 2 Signal Faulted ABS Module Go to Pinpoint Test E .
C1279 Yaw Rate Sensor Circuit Failure ABS Module Go to Pinpoint Test F .
C1280 Yaw Rate Sensor Signal Fault ABS Module Go to Pinpoint Test F .
C1281 Lateral Accelerometer Circuit Failure ABS Module Go to Pinpoint Test F .
C1282 Lateral Accelerometer Signal Fault ABS Module Go to Pinpoint Test F .
C1288 Brake Pressure Transducer Main/Primary Input Circuit Failure ABS Module Go to Pinpoint Test G .
C1446 Brake Switch Circuit Failure ABS Module Go to Pinpoint Test H .
C1516 Roll Rate Sensor Signal Fault ABS Module Go to Pinpoint Test F .
C1517 Roll Rate Sensor Circuit Fault ABS Module Go to Pinpoint Test F .
C2769 Longitudinal Acceleration Sensor Electrical Failure ABS Module Go to Pinpoint Test F .
C2770 Longitudinal Acceleration Sensor Plausibility Failure ABS Module Go to Pinpoint Test F .
U1901 CAN Network #2 Comm Bus Fault - Receive Error ABS Module
NOTE: If other DTCs are present, REPAIR them to diagnosing DTC U1901.
Go to Pinpoint Test J .
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.