Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Ford Edge FWD V6-3.5LFACTORY OEM SERVICE PROCEDURE
Keyless Entry Key-Pad: Testing and Inspection
KEYLESS ENTRY KEYPAD CODE PROGRAMMING
Programming a Personal Code and Keypad Association to Memory Seats and Mirrors (If Equipped)
NOTE:
- If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after one minute of keypad inactivity, after pressing the UNLOCK control on the integrated keyhead transmitter (IKT), or after the ignition key has been turned to the ON position.
- The factory set code cannot be associated with a memory setting.
1. Enter the permanent factory keyless entry keypad code.
2. Within 5 seconds, press the 1/2 button on the keypad.
3. Enter the new 5-digit keyless entry keypad code. Each number must be entered within five seconds of each other.
4. To associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code:
- Pressing the 1/2 button recalls driver 1 settings
- Pressing the 3/4 button recalls driver 2 settings
- Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not set a driver and will not recall a memory setting
5. The doors will lock then unlock to confirm the new code is programmed.
Erasing the Personal Codes
NOTE: If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after one minute of keypad inactivity, after pressing the UNLOCK control on the IKT, or after the ignition key has been turned to the ON position.
1. Enter the permanent factory keyless entry keypad code.
2. Within 5 seconds, press the 1/2 button on the keypad and release.
3. Within 5 seconds, press and hold the 1/2 button on the keypad for 2 seconds.
4. All personal codes are now erased and only the permanent factory keyless entry keypad code will work.
Programming a Personal Code and Keypad Association to Memory Seats and Mirrors (If Equipped)
NOTE:
- If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after one minute of keypad inactivity, after pressing the UNLOCK control on the integrated keyhead transmitter (IKT), or after the ignition key has been turned to the ON position.
- The factory set code cannot be associated with a memory setting.
1. Enter the permanent factory keyless entry keypad code.
2. Within 5 seconds, press the 1/2 button on the keypad.
3. Enter the new 5-digit keyless entry keypad code. Each number must be entered within five seconds of each other.
4. To associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code:
- Pressing the 1/2 button recalls driver 1 settings
- Pressing the 3/4 button recalls driver 2 settings
- Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not set a driver and will not recall a memory setting
5. The doors will lock then unlock to confirm the new code is programmed.
Erasing the Personal Codes
NOTE: If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after one minute of keypad inactivity, after pressing the UNLOCK control on the IKT, or after the ignition key has been turned to the ON position.
1. Enter the permanent factory keyless entry keypad code.
2. Within 5 seconds, press the 1/2 button on the keypad and release.
3. Within 5 seconds, press and hold the 1/2 button on the keypad for 2 seconds.
4. All personal codes are now erased and only the permanent factory keyless entry keypad code will work.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.