Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Ford Taurus SE, 3.0 2FACTORY OEM SERVICE PROCEDURE
Anti-Lock Control DTCS
ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1596 | Service Continuous Code | ABS/TC | TURN the ignition switch from OFF to ON. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC CODE (DTC) INDEX . If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the SYMPTOM CHART . |
| B1676 | Battery Pack Voltage Out of Range | ABS/TC | GO to PINPOINT TEST B . |
| B1342 | ECU is Faulted | ABS/TC | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is retrieved again, INSTALL a new ABS module. REPEAT the self-test. |
| B1484 | Brake Pedal Input Open Circuit | ABS/TC | GO to PINPOINT TEST C . |
| C1300 | ABS Pump Motor Circuit Failure | ABS/TC | GO to PINPOINT TEST D . |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1222 | Speed Wheel Mismatch | ABS/TC | GO to PINPOINT TEST F . |
| C1296 | Wheel Speed LF Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1297 | Wheel Speed RF Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1298 | Wheel Speed RR Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1299 | Wheel Speed LR Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1266 | ABS Valve Power Relay Circuit Failure | ABS/TC | GO to PINPOINT TEST G . |
| U0073 | Control Module Communication Bus Off Fault | Network Fault | Refer to MODULE COMMUNICATIONS NETWORK . |
| U1900 | CAN Communication Bus Fault-Receive Error | Network Fault | Refer to MODULE COMMUNICATIONS NETWORK . |
| U2023 | Fault Received From External Node | Network Fault | Refer to MODULE COMMUNICATIONS NETWORK . |
| C1805 | Mismatched PCM and/or ABS-TC Module | ABS/TC | CARRY OUT the PCM self-test. CHECK for correct PCM and ABS module part numbers. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
