2006 Ford Freestar BaseFACTORY OEM SERVICE PROCEDURE

Automatic Transmission: Removal: Transaxle

SPECIAL TOOL(S)

G04661154Courtesy of FORD MOTOR CO.
Lifting Bracket Set, Engine
303-D095 (D94L-6001-A) or equivalent
G04661155Courtesy of FORD MOTOR CO.
Extension
205-243 (T86P-3514-A2)
G04661156Courtesy of FORD MOTOR CO.
Slide Hammer
100-001 (T50T-100-A)
G04661157Courtesy of FORD MOTOR CO.
Support Bar, Engine
303-290A
G04661158Courtesy of FORD MOTOR CO.
Adapter for
303-290A (Support Leg) 303-290A-03A
G04661159Courtesy of FORD MOTOR CO.
Remover, Halfshaft
205-832
G04661160Courtesy of FORD MOTOR CO.
Adapter for
303-290A (Spreader Bar) 303-290A-10
G04661161Courtesy of FORD MOTOR CO.
Separator, Tie-Rod End
211-105
G04661162Courtesy of FORD MOTOR CO.
Adapter for 303-290A (Support Bracket)
303-290A-11
G04661163Courtesy of FORD MOTOR CO.
Adapter for 303-290A (Strut)
303-290A-09
    NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive shift strategy.
  1. Remove the battery. For additional information, refer to BATTERY, MOUNTING AND CABLES .
  2. Loosen the clamps and remove the air cleaner tube.
    Fig 1: Locating Air Cleaner Tube And Clamps
    G04661164Courtesy of FORD MOTOR CO.
  3. Remove the air cleaner assembly. For additional information, refer to INTAKE AIR DISTRIBUTION AND FILTERING .
    Fig 2: Locating Air Cleaner Assembly
    G04661165Courtesy of FORD MOTOR CO.
  4. Disconnect the electrical connectors.
    1. Disconnect the digital transmission range (TR) sensor electrical connector.
    2. Disconnect the transaxle electrical connector.
    3. Disconnect the speed control electrical connector.
      Fig 3: Identifying Digital Transmission Range (TR) Sensor Electrical Connector
      G04661166Courtesy of FORD MOTOR CO.
  5. Remove the transmission selector cable from the bracket.
    1. Disconnect the transmission selector cable end from the manual lever.
    2. Push the lock tab and separate the transmission selector cable from the bracket.
    3. Position the transmission selector cable aside.
      Fig 4: Identifying Transmission Selector Cable From Bracket
      G04661167Courtesy of FORD MOTOR CO.
  6. Disconnect the wire harness from the bracket.
    Fig 5: Locating Wire Harness Bracket
    G04661168Courtesy of FORD MOTOR CO.
  7. Remove the manual control lever.
    Fig 6: Locating Manual Control Lever
    G04661169Courtesy of FORD MOTOR CO.
  8. Remove the hood.
  9. Remove the wiper arm and pivot assembly. For additional information, refer to WIPERS AND WASHERS .
  10. Remove the passenger compartment air intake box.
    Fig 7: Locating Passenger Compartment Air Intake Box
    G04661170Courtesy of FORD MOTOR CO.
  11. Remove the air intake tube.
    Fig 8: Locating Air Intake Tube
    G04661171Courtesy of FORD MOTOR CO.
  12. Remove the front upper radiator shield.
    Fig 9: Locating Front Upper Radiator Shield
    G04661172Courtesy of FORD MOTOR CO.
  13. Remove the hood latch and position aside.
    Fig 10: Locating Hood Latch Position
    G04661173Courtesy of FORD MOTOR CO.
  14. Remove the oil filler cap.
    Fig 11: Locating Oil Filler Cap
    G04661174Courtesy of FORD MOTOR CO.
  15. Install the special tool (front of engine compartment).
    Fig 12: Identifying Special Tool (303-D095) (Front Of Engine Compartment)
    G04661175Courtesy of FORD MOTOR CO.
  16. Install the special tool (rear of engine compartment).
    Fig 13: Identifying Special Tool (303-D095) (Rear Of Engine Compartment)
    G04661176Courtesy of FORD MOTOR CO.
  17. Install the special tools.
    Fig 14: Identifying Special Tools (303-290A-03A, 303-290A-09, 303-290A-10, 303-290A, 303-D095)
    G04661177Courtesy of FORD MOTOR CO.
  18. Remove the bolt and the upper fluid filler tube.
    Fig 15: Locating Upper Fluid Filler Tube Bolts
    G04661178Courtesy of FORD MOTOR CO.
  19. Remove the fluid cooler tube retaining clips.
    Fig 16: Locating Fluid Cooler Tube Retaining Clips
    G04661179Courtesy of FORD MOTOR CO.
  20. Depress the tabs on the plastic insert retainer and remove the cooler line from the fitting.
    Fig 17: Locating Plastic Retainer
    G04661180Courtesy of FORD MOTOR CO.
  21. Remove the 2 transaxle retaining bolts.
    Fig 18: Locating Transaxle Retaining Bolts
    G04661181Courtesy of FORD MOTOR CO.
  22. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING AND LIFTING .
  23. Remove the bolts and remove the anti-roll bracket.
    Fig 19: Locating Anti-Roll Bracket And Bolts
    G04661182Courtesy of FORD MOTOR CO.
  24. Remove the rear transaxle support nut.
    Fig 20: Locating Rear Transaxle Support Nut
    G04661183Courtesy of FORD MOTOR CO.
  25. Drain the transmission fluid by lowering the transaxle pan.
  26. NOTE: The transaxle fluid pan does not need to be tightened in this step.
  27. Install the transaxle pan.
  28. Remove the catalytic converter assembly. For additional information, refer to EXHAUST SYSTEM .
  29. Disconnect the LH knuckle assembly.
    1. Disconnect the LH tie-rod assembly.
    2. Disconnect the LH sway bar assembly.
    3. Remove the LH pinch bolt.
      Fig 21: Identifying LH Tie Rod, Sway Bar Assembly And Pinch Bolt
      G04661184Courtesy of FORD MOTOR CO.
  30. CAUTION: Do not damage the tie-rod end boot when installing the special tool.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.