2006 Ford Freestar BaseFACTORY OEM SERVICE PROCEDURE

Torque Specifications

TORQUE SPECIFICATIONS

Description Nm lb-ft lb-in
A/C compressor manifold bolt 20 15 -
A/C compressor mounting bracket brace lower bolts 25 18 -
A/C compressor mounting bracket brace upper bolts 47 35 -
Accelerator cable bracket bolt 10 - 89
Accelerator cable bracket nut 10 - 89
Accessory drive belt tensioner bolts 25 18 -
Air inlet duct nuts 5 - 44
B+ wire terminal nut 8 - 71
Balance shaft bolts 11 8 -
Bellhousing bolts 90 66 -
Block heater 2 - 18
Brake calipers 35 26 -
Camshaft position sensor (CMP) bolts 3 - 27
Camshaft synchronizer assembly bolt 25 18 -
Camshaft thrust plate bolts 11 8 -
Catalyst monitor sensor (CMS) electrical connector bracket nut 28 21 -
CMP sensor drive gear bolt 45 33 -
Connecting rod cap bolts(1) - - -
Coolant bypass tube bolt 10 - 89
Coolant pump bolts(1) - - -
Coolant pump extension tube bolt 25 18 -
Coolant pump nuts(1) - - -
Coolant pump outlet tube bolt 10 - 89
Coolant pump pulley bolts 11 8 -
Cowl top panel bolts 6 - 53
Crankshaft main bearing cap bolts(1) - - -
Crankshaft position (CKP) sensor nuts 6 - 53
Crankshaft pulley bolt 160 118 -
Cylinder head bolts(1) - - -
EGR system module bolts 25 18 -
Engine front cover bolts(1) - - -
Engine front cover studs 7 - 62
Engine harness ground bolts 10 - 89
Engine roll restrictor bolts 63 46 -
Engine roll restrictor bracket upper bolt 30 22 -
Engine roll restrictor bracket lower bolts 90 66 -
Engine-to-transaxle bolts 50 37 -
Exhaust gas recirculation (EGR) tube nuts 40 30 -
Exhaust manifold nuts 25 18 -
Exhaust manifold studs 8 - 71
Flywheel-to-crankshaft bolts 80 59 -
Front subframe bolts 175 129 -
Fuel rail bolts 10 - 89
Generator bolts 25 18 -
Generator brace bolt 47 35 -
Ground cable 10 - 89
Heater shield nuts 10 - 89
Heater tube bolt 10 - 89
Idler pulley bolt 47 35 -
Ignition coil bolts 6 - 53
Inspection cover plate bolt 10 - 89
LH motor mount bolt 90 66 -
LH motor mount-to-subframe nut 90 66 -
Lower engine mount nuts 80 59 -
Lower intake manifold bolts(1) - - -
Oil bypass filter-to-oil pump and filter body(1) - - -
Oil cooler and tube assembly bolt 35 26 -
Oil cooler mounting bolt 35 26 -
Oil filter housing bolts(1) - - -
Oil level indicator tube and bracket bolt 10 - 89
Oil pan baffle nuts 32 24 -
Oil pan bolts(1) - - -
Oil pan drain plug 26 19 -
Oil pan-to-transaxle mounting bolt (W506035-S439) 48 35 -
Oil pickup tube and screen bolts 25 18 -
Oil pickup tube and screen nut 48 35 -
Oil pressure sensor 27 20 -
Oil pump and filter body-to-engine front cover bolts (large) 25 18 -
Oil pump and filter body-to-engine front cover bolts (small) 10 - 89
Power steering pump bracket (large) bolts 48 35 -
Power steering pump bracket (small) bolts 25 18 -
Powertrain control module (PCM) bolt 10 - 89
Rear motor mount-to-bracket nut 63 46 -
Rear motor mount-to-subframe nut 90 66 -
RH motor mount bracket bolts 48 35 -
RH motor mount-to-bracket bolt 90 66 -
RH motor mount-to-subframe nut 90 66 -
Rocker arm-to-cylinder head bolt(s)(1) - - -
Spark plugs 15 11 -
Stabilizer bar link upper nuts N807144-S427 (vehicles built through 12/2005) 90 66 -
Stabilizer bar link upper nuts N712111-S440 (vehicles built after 12/2005) 103 76 -
Steering column bolt (N808349-S439) 30 22 -
Strut bolts 115 85 -
Suction/discharge manifold and tube assembly bolt 20 15 -
Synchronizer drive gear bolt 45 33 -
Tappet guide plate bolts 12 9 -
Tensioner pulley bracket bolts 25 18 -
Timing chain tensioner bolts 11 8 -
Torque converter nuts 36 27 -
Transaxle fluid level indicator tube bolt 10 - 89
Transaxle support insulator nut 90 66 -
Upper intake manifold bolts(1) - - -
Valve cover bolts 10 - 89
Valve cover stud bolts 10 - 89
(1) Refer to the procedure in this article.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.