Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Ford Expedition RWDFACTORY OEM SERVICE PROCEDURE
Anti-Lock Brake System
- Specifications
- Description And Operation
- Diagnosis And Testing
- Anti-Lock Control
- Notes
- Principles of Operation
- Anti-Lock Brake System (ABS)
- Electronic Brake Distribution (EBD)
- Panic Assist Braking (ABS With Stability Assist)
- Stability Assist
- Roll Stability Control (RSC)
- Stability Control Sensor Cluster (ABS With Stability Assist)
- Steering Wheel Rotation Sensor (ABS With Stability Assist)
- Active Brake Booster (ABS With Stability Assist)
- ABS Module Configuration
- ABS Module Calibration (ABS With Stability Assist)
- Anti-Lock Brake System (Abs) Module Diagnostic Trouble Code (DTC) Index
- Symptom Table
- Pinpoint Tests
- Pinpoint Test A: No Communication With The Anti-Lock Brake System (ABS) Module
- Pinpoint Test B: DTC B1483 - Brake Pedal Input Circuit Failure
- Possible Causes
- Pinpoint Test C: DTC B1676 - Battery Pack Voltage Out Of Range
- Pinpoint Test D: DTC C1095 - ABS Hydraulic Pump Motor Circuit Failure
- Pinpoint Test E: DTC C1145 (RF), DTC C1155 (LF), DTC C1165 (RR), DTC C1175 (LR) - Speed Wheel Sensor Input Circuit Failure
- Pinpoint Test F: DTC C1233 (LF), DTC C1234 (RF), DTC C1235 (RR), DTC C1236 (LR) - Speed Wheel Input Signal Missing
- Pinpoint Test G: DTC C1277 AND C1278 - Steering Wheel Angle 1 And 2 Circuit Failure/Signal Faulted
- Pinpoint Test H: DTC C1279, C1280, C1281, C1282, C1516, C1517, C2769, C2770, C2777, C2778 - Sensor Cluster Fault
- Pinpoint Test I: DTC C1285 - Booster Solenoid Circuit Failure
- Pinpoint Test J: DTC C1287 - Brake Booster Pedal Force Switch Circuit Failure
- Pinpoint Test K: DTC C1288 AND C1440 (ABS With Stability Assist) - Brake Pressure Sensor Input Circuit Failure/Signal Faulted
- Pinpoint Test L: DTC C1730 - Reference Voltage Out Of Range (+5 V)
- Pinpoint Test M: DTC B2734, B2736, B2737, B2738, B2740 - Pedal Travel Sensor Fault
- Pinpoint Test N: The Stability System Assist Cannot Be Disabled
- Pinpoint Test O: DTC C1998 - Module Calibration Not Complete
- Pinpoint Test P: The Stability Assist Switch Indicator Is Never/Always On
- Anti-Lock Control
- Removal And Installation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
