Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Ford Freestar BaseFACTORY OEM SERVICE PROCEDURE
Left Power Sliding Door Module (LPSDM)
DTC CHART (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1342 | ECU Is Defective | LPSDM | CLEAR the DTCs. CARRY OUT the LPSDM self-test. If DTC B1342 is retrieved, INSTALL a new LPSDM. |
| B2238 | Broken Cable Detected | LPSDM | GO to PINPOINT TEST C . |
| B2270 | PSD Exceeded Time Allowed To Cinch Door (Exceeded Time Allowed To Reach Primary Latch Position After Reaching Secondary Latch Position) | LPSDM | GO to PINPOINT TEST D . |
| B2271 | PSD Did Not Reach Full-Open Position During Self-Test | LPSDM | GO to PINPOINT TEST E . |
| B2363 | Position Sensor System Failure | LPSDM | GO to PINPOINT TEST F . |
| B2364 | Fuel Door Interlock Open Circuit | LPSDM | GO to PINPOINT TEST G . |
| B2365 | B-Pillar Power Sliding Door Open/Close Switch Circuit Short To Ground | LPSDM | GO to PINPOINT TEST H . |
| B2366 | PSD Open/Close Switch Circuit Short To Ground | LPSDM | GO to PINPOINT TEST I . |
| B2374 | PSD Detent Switch Circuit Short To Ground | LPSDM | GO to PINPOINT TEST J . |
| B2483 | Enable Signal Open Circuit (Park) | LPSDM | GO to PINPOINT TEST K . |
| B2589 | No PSD Detent Switch Detected On Closing And Door Reversed | LPSDM | GO to PINPOINT TEST L . |
| B2591 | No PSD Detent Switch Detected On Unlatch | LPSDM | GO to PINPOINT TEST M . |
| B2592 | Door Not Pulled Into Primary During Power Close And High Duty Cycles | LPSDM | GO to PINPOINT TEST N . |
| B2593 | Door Reversed While Closing Due To An Obstacle | LPSDM | GO to PINPOINT TEST O . |
| B2594 | No Movement Was Detected After An Unlatch During A Power Open Operation | LPSDM | GO to PINPOINT TEST P . |
| B2603 | PSD Not Fully Closed During Self-Test | LPSDM | GO to PINPOINT TEST Q . |
| B2604 | PSD On/Off Switch Open Circuit | LPSDM | GO to PINPOINT TEST R . |
| B2605 | Disable Signal Open Circuit - VSS greater than 5 km/h (3 mph) | LPSDM | GO to PINPOINT TEST S . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.