2004 Ford Freestar BaseFACTORY OEM SERVICE PROCEDURE

Automatic Transmission: Removal: Transaxle

Special Tool(s)Β 

Fig 1: Special Tools Specifications
G03244631Courtesy of FORD MOTOR CO.
    NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive shift strategy.
  1. Remove the battery. For additional information, refer to BATTERY & CHARGING SYSTEM .
  2. Loosen the clamps and remove the air cleaner tube.
    Fig 2: Removing Air Cleaner Tube
    G03244632Courtesy of FORD MOTOR CO.
  3. Remove the air cleaner assembly. For additional information, refer to AIR CLEANER ASSEMBLY .
    Fig 3: Removing Air Cleaner Assembly
    G03244633Courtesy of FORD MOTOR CO.
  4. Disconnect the electrical connectors.
    1. Disconnect the digital transmission range (TR) sensor electrical connector.
    2. Disconnect the transaxle electrical connector.
    3. Disconnect the speed control electrical connector.
    Fig 4: Disconnecting Electrical Connectors
    G03244634Courtesy of FORD MOTOR CO.
  5. Remove the transmission selector cable from the bracket.
    1. Disconnect the transmission selector cable end from the manual lever.
    2. Push the lock tab and separate the transmission selector cable from the bracket.
    3. Position the transmission selector cable out of the way.
    Fig 5: Removing Transmission Selector Cable From Bracket
    G03244635Courtesy of FORD MOTOR CO.
  6. Disconnect the wire harness from the bracket.
    Fig 6: Disconnecting Wire Harness From Bracket
    G03244636Courtesy of FORD MOTOR CO.
  7. Remove the manual control lever.
    Fig 7: Removing Manual Control Lever
    G03244637Courtesy of FORD MOTOR CO.
  8. Remove the hood.
  9. Remove the wiper arm and pivot assembly. For additional information, refer to WINDSHIELD WIPER
  10. Remove the passenger compartment air intake box.
    Fig 8: Removing Passenger Compartment Air Intake Box
    G03244638Courtesy of FORD MOTOR CO.
  11. Remove the air intake tube.
    Fig 9: Removing Air Intake Tube
    G03244639Courtesy of FORD MOTOR CO.
  12. Remove the front upper radiator shield.
    Fig 10: Removing Front Upper Radiator Shield
    G03244640Courtesy of FORD MOTOR CO.
  13. Remove the hood latch and position aside.
    Fig 11: Removing Hood Latch
    G03244641Courtesy of FORD MOTOR CO.
  14. Remove the oil filler cap.
    Fig 12: Removing Oil Filler Cap
    G03244642Courtesy of FORD MOTOR CO.
  15. Install the special tool (front of engine compartment).
    Fig 13: Installing Special Tool To Front Of Engine
    G03244643Courtesy of FORD MOTOR CO.
  16. Install the special tool (rear of engine compartment).
    Fig 14: Installing Special Tool To Rear Of Engine
    G03244644Courtesy of FORD MOTOR CO.
  17. Install the special tools.
    Fig 15: Installing Special Tools
    G03244645Courtesy of FORD MOTOR CO.
  18. Remove the bolt and the upper fluid filler tube.
    Fig 16: Removing Upper Fluid Filler Tube
    G03244646Courtesy of FORD MOTOR CO.
  19. Remove the fluid cooler tube retaining clips.
    Fig 17: Removing Fluid Cooler Tube Retaining Clips
    G03244647Courtesy of FORD MOTOR CO.
  20. Depress the tabs on the plastic insert retainer and remove the cooler line from the fitting.
    Fig 18: Removing Cooler Line From Fitting
    G03244648Courtesy of FORD MOTOR CO.
  21. Remove the two transaxle retaining bolts.
    Fig 19: Removing Transaxle Retaining Bolts
    G03244649Courtesy of FORD MOTOR CO.
  22. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING & LIFTING .
  23. Remove the bolts and remove the anti-roll bracket.
    Fig 20: Removing Anti-Roll Bracket
    G03244650Courtesy of FORD MOTOR CO.
  24. Remove the rear transaxle support nut.
    Fig 21: Removing Rear Transaxle Support Nut
    G03244651Courtesy of FORD MOTOR CO.
  25. Drain the transmission fluid by lowering the transaxle pan.
  26. NOTE: The transaxle fluid pan does not need to be tightened in this step.
  27. Install the transaxle pan.
  28. Remove the catalytic converter assembly. For additional information, refer to EXHAUST SYSTEM .
  29. Disconnect the LH knuckle assembly.
    1. Disconnect the LH tie rod assembly.
    2. Disconnect the LH sway bar assembly.
    3. Remove the LH pinch bolt.
    Fig 22: Disconnecting LH Knuckle Assembly
    G03244652Courtesy of FORD MOTOR CO.
  30. CAUTION: Do not damage the tie-rod end boot when installing the special tool.
Chapter Navigation
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.