Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Ford ZX2 AutomaticFACTORY OEM SERVICE PROCEDURE
Parameter Identification & Definitions
PID DEFINITIONS (ABS CONTROL MODULE)
| PID | Description | Expected Value |
|---|---|---|
| CCNTABS | Number Of Continuous DTCs | One Count Per Bit |
| ABSLAMP | ABS Warning Light State | ON, OFF |
| BLSHORT | ABS Warning Light State | ON, OFF |
| BOO_ABS | Brake Pedal Position Switch Input | ON, OFF |
| BRKLAMP | Brake Warning Light State | ON, OFF |
| LF_WSPI | Left Front Wheel Speed Sensor Signal | 0-255 MPH |
| LR_WSPI | Left Rear Wheel Speed Sensor Signal | 0-255 MPH |
| PWR_RLY | Power Relay Feedback Input | ON, OFF |
| RESETSW | Rear Reset Switch Input | ON, OFF |
| RF_WSPI | Right Front Wheel Speed Sensor Signal | 0-255 MPH |
| RR_WSPI | Right Rear Wheel Speed Sensor Signal | 0-255 MPH |
PID DEFINITIONS (ECS MODULE) (1)
| PID | Description | Expected Value | ||
|---|---|---|---|---|
| CCNTECS | Number Of Continuous DTCs | One Count Per Bit (0-16) | ||
| DABAGR | Driver's Side Air Bag Module Resistance | 1.8-4.1 Ohms | ||
| PABAGR | Passenger's Side Air Bag Module Resistance | 1.4-3.6 Ohms | ||
| BRACKET | Bracket Ground Resistance | Less Than 100 Ohms | ||
| VBATECS | System Battery Voltage | 9-16 Volts | ||
|
||||
PID DEFINITIONS (RAP MODULE)
| PID | Description | Expected Value | ||||
|---|---|---|---|---|---|---|
| AL_EVT# | Last 8 Alarm Events | HOODDTR, NO_EVT, DROPEN, PANIC, TRAJAR | ||||
| HOOD_SW | Hood Switch State | PUNCHD, not PUN | ||||
| DOORRAP | Door Ajar Status Input | CLOSED, AJAR | ||||
| IGN_RAP | Ignition Switch | OFF, RUN | ||||
| DD_RAP | Power Door Unlock Status | OFF, UNLOCK | ||||
| NOTHEFT | No Theft Jumper | NO, YES | ||||
| NOREMOTE | No Remote Jumper | NO, YES | ||||
| DECKLD | Trunk Ajar Status Input | AJAR, CLOSED | ||||
| LEDFLASH (1) | LED Flash When Armed | ENABLED, DISABLED | ||||
| HORNCHIRP (1) | Program Chirp Status (2) | ENABLED, DISABLED | ||||
|
||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.