2000 Ford Contour SVTFACTORY OEM SERVICE PROCEDURE

Enabling & Disabling Features On Remote Anti-Theft

WARNING: This page does not describe the selected car, but rather 26 other vehicles, including the 1999 Mercury Villager, 1999 Mercury Tracer, 1999 Mercury Sable, 1999 Mercury Mystique, and 1999 Mercury Mountaineer. However, it is still accessible from the selected car via links, so may be relevant.

Personality Module

Enable/disable mode allows technician to set alarm configuration to match the laws for alarm operation in the country where vehicle is to be driven. Enable/disable mode will also enable/disable autolock. Alarm configurations are set by assembly plant for regulations in expected destination and should not be modified for use in other countries. Remote keyless entry transmitter PANIC will share exterior lights and horn characteristics. PANIC alarm will also turn on interior lights in all cases for 25 seconds.

NOTE: Step 2) must be completed within 30 seconds of turning ignition switch to RUN position in step 1). While in enable/disable mode, RAP module will not have any other functionality except enabling/disabling features. Enabling a new alarm configuration will automatically disable previous alarm configuration.
  1. Ensure anti-theft system is not armed or triggered. Turn ignition switch to LOCK position. Close all doors. Turn ignition switch from LOCK to RUN position.
  2. Press power door UNLOCK button 3 times. Turn ignition switch from RUN to LOCK position. Press power door UNLOCK button 3 times. Turn ignition switch back to RUN position. If enable/disable mode has been entered successfully, horn will chirp.
  3. Press power door UNLOCK button number of times associated with function you would like to enable or disable as shown in table. See ENABLE/DISABLE FUNCTIONS table. Press power door LOCK button once after last UNLOCK button press in order to enter enable/disable code. System will confirm altered function by chirping horn same number of times as number of unlock presses registered. If function has been enabled, a long horn sound will follow sequence of horn chirps. If function has been disabled, no horn sound will follow sequence of horn chirps.
  4. After horn chirp sequence has occurred in enable/disable mode, another function may be enabled or disabled. To exit enable/disable mode, turn ignition switch to LOCK position or allow 5 minutes to pass after entering enable mode. After exiting, system will confirm exit with horn chirp if a function has been changed.
ENABLE/DISABLE FUNCTIONS

Function Press Unlock Button
Autolock/Relock 1 Time
North America/Gulf Coast/Korea Alarm (1) 5 Times
Europe/Australia Alarm (1) 6 Times
(1) Locations not listed use North America standards.
NOTE: This procedure is used when a customer needs keys programmed into system and does not have 2 programmed ignition keys available, or when programmed ignition keys have been lost and/or ignition switch assembly has been replaced. This procedure will erase all programmed ignition keys from memory and prevent vehicle from starting until 2 keys have been programmed. Ignition keys must have correct mechanical key cut for vehicle and must be an encoded key. If additional key(s) are to be programmed, perform KEY PROGRAMMING - USING 2 PROGRAMMED KEYS. If remaining keys are with customer and not with vehicle, instruct customer to see owner's manual to program spare key(s).
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.