Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1997 Ford Contour Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Specifications Index
(CONTOUR & MYSTIQUE) SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM GENERAL SERVICING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 210 ft. lbs. (285 N.m) | ||
| Rear | 170-192 ft. lbs. (230-260 N.m) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| 2.0L | |||
| Adjustment | BELT ADJUSTMENT | ||
| Drive Belt Routing | DRIVE BELT ROUTING | ||
| 2.5L | |||
| Adjustment | BELT ADJUSTMENT | ||
| Drive Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.0L | COOLING SYSTEM SPECIFICATIONS | ||
| 2.5L | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 11-13 psi | ||
| Thermostat R & I | |||
| 2.0L | THERMOSTAT | ||
| 2.5L | THERMOSTAT | ||
| Water Pump R & I | |||
| 2.0L | WATER PUMP | ||
| 2.5L | WATER PUMP | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | ENGINE SPECIFICATIONS | ||
| Oil Pressure | 20-45 psi (1.4-3.2 kg/cm 2 ) at 1500 RPM | ||
| Overhaul | OVERHAUL | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2.5L | |||
| Compression | ENGINE SPECIFICATIONS | ||
| Oil pressure | 20-45 psi (1.4-3.2 kg/cm 2 ) at 1500 RPM | ||
| Overhaul | OVERHAUL | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | 54-64 ft. lbs. (73-87 N.m) | ||
| Fuel System | |||
| 2.0L | |||
| Pressure Specification | FUEL PRESSURE | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE | ||
| Fuel Filter Location | FUEL SYSTEM | ||
| Fuel Filter R & I | FUEL SYSTEM | ||
| 2.5L | |||
| Pressure Specification | FUEL PRESSURE | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE | ||
| Fuel Filter Location | FUEL SYSTEM | ||
| Fuel Filter R & I | FUEL SYSTEM | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.0L | FIRING ORDER & TIMING MARKS | ||
| 2.5L | FIRING ORDER & TIMING MARKS | ||
| 2.0L | Coil On Plug IGNITION COIL |
||
| 2.5L | Coil On Plug IGNITION COIL |
||
| Ignition Wires (Resistance) | |||
| 2.0L | HIGH TENSION WIRE RESISTANCE | ||
| 2.5L | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | |||
| 2.0L | IGNITION SYSTEM | ||
| 2.5L | IGNITION SYSTEM | ||
| Spark Plug | |||
| 2.0L (Motorcraft AZFS-32F) | |||
| Gap | 0.048-0.052 In. (1.20-1.32 mm) | ||
| Torque | 9-13 ft. lbs. (13-17 N.m) | ||
| 2.5L (Motorcraft AWSF-32F) | |||
| Gap | 0.052-0.056 In. (1.32-1.42 mm) | ||
| Torque | 7-15 ft. lbs. (9-20 N.m) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | ADJUSTMENTS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 85-105 ft. lbs. (115-142 N.m) | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
