Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1996 Ford Probe GT, StandardFACTORY OEM SERVICE PROCEDURE
External Pages
These are pages that do not belong to the exact selected vehicle (1996 Ford Probe GT, Standard), but are still accessible from a link in your vehicle's manual. Be very cautious using repair info from here because these pages may not apply to your vehicle.
- Different variant/trim
- Section 1 (Engine Controls - Specifications - 2.0L)
- Section 2 (Engine Controls - Adjustments - 2.0L)
- Section 3 (Engine Controls - Basic Testing - 2.0L)
- Section 4 (Engine Controls - Tests W/Codes - 2.0L)
- Section 5 (Engine Controls - Tests W/O Codes - 2.0L)
- Section 6 (Engine Controls - Pin Voltage Charts - 2.0L)
- Section 7 (Engine Controls - Remove/Install/Overhaul - 2.0L)
- Section 8 (Engine Cooling System Specifications & Drive Belt Routing - 4-CYL)
- Section 9 (Automatic Transmission Removal & Installation)
- Section 10 (Engine - 2.0L 4-CYL - VIN [A])
- Section 11 (Diagnosis - Cd4E - EEC-V Automatic Transmission)
- Different car
- Section 1 (Computer Relearn Procedures)
- Section 2 (Engine Controls - Tests W/Codes - EEC (2.5L))
- Section 3 (Engine/VIN Id)
- Section 4 (Engine Controls - Adjustments - 2.5L)
- Section 5 (Engine Controls - Tests W/Codes - EEC-IV (2.5L))
- Section 6 (Engine Controls - Remove/Install/Overhaul - 2.5L)
- Section 7 (Engine Controls - Remove/Install/Overhaul - 2.5L)
- Section 8 (Engine Controls - Theory & Operation - 2.5L)
- Section 9 (Wiring Diagrams - 2.5L)
- Section 10 (Engine Controls - System/Component Tests - EEC-IV (2.5L))
- Section 11 (Vacuum Diagrams - 2.5L)
- Section 12 (Engine Controls - Basic Testing - 2.5L)
- Section 13 (Engine Controls - Tests W/O Codes - EEC-IV (2.5L))
- Section 14 (Engine Controls - Basic Testing - 2.5L)
- Section 15 (Wiring Diagrams - 2.5L)
- Section 16 (Engine Controls - Tests W/O Codes - EEC (2.5L))
- Section 17 (Engine Controls - Pin Voltage Charts - EEC-IV (2.5L))
- Section 18 (Engine Controls - Specifications - 2.5L)
- Section 19 (Engine Controls - Sensor Operating Range Charts - EEC-IV (2.5L))
- Section 20 (Supplemental Inflatable Restraint System)
- Section 21 (Heater System)
- Section 22 (Axle Shafts - Front)
- Section 23 (Axle Shafts - Front)
- Section 24 (Axle Shafts - Front)
- Section 25 (Axle Shafts - Front)
- Section 26 (Removal & Installation - M/T)
- Section 27 (Rear Electronic Suspension System)
- Section 28 (Axle Shafts - Front)
- Section 29 (Servicing - M/T)
- Section 30 (Drive Shafts)
- Section 31 (Axle Shafts - Front)
- Section 32 (Automatic Transmission Servicing)
- Section 33 (Fuel Pressure Specifications)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
