1995 Ford Bronco 5.8 HFACTORY OEM SERVICE PROCEDURE

Engine Controls - Specifications - 5.8L: Capacities

BATTERY SPECIFICATIONS

Application & Group Cold Cranking Amps
Standard BXT-65 650
Optional BXT-65 850
COOLING SYSTEM CAPACITIES

Application Qts. (L)
Bronco & Pickup 15.0-17.0 (14.0-16.0)
Van
Standard Cooling 20.0 (19.0)
A/C Or Super Cooling 23.0 (20.0)
CRANKCASE CAPACITIES

Application (1) Qts. (L)
5.8L (2) 5.0 (4.70)
(1) Add 1/2 qt. if equipped with oil cooler.
(2) On Pickup, 6 quarts (5.6L).
TRANSMISSION & TRANSFER CASE CAPACITIES

Application Specification Quantity
Bronco
AOD Auto. Mercon 12.3 Qts. (11.6L)
C-6 Auto. (4WD) Mercon 13.5 Qts. (12.7L)
E4OD Auto. (2WD) Mercon 16.2 Qts. (15.3L)
4-Speed (Warner T-18) SAE 80W-90 3.5 Qts. (3.3L)
5-Speed Overdrive (Mazda R-2) Mercon 3.8 Qts. (3.6L)
Transfer Case (Warner 13-56) Mercon 2.0 Qts. (1.9L)
Pickup
AOD Auto. (2WD) Mercon 12.3 Qts. (11.6L)
C-6 Auto. (2WD) Mercon 12.0 Qts. (11.4L)
C-6 Auto. (4WD) Mercon 13.5 Qts. (12.7L)
E4OD Auto. (2WD) Mercon 15.7 Qts. (14.8L)
E4OD Auto. (4WD) Mercon 16.2 Qts. (15.3L)
4-Speed (Warner T-18) SAE 80W-90 3.5 Qts. (3.3L)
5-Speed Overdrive
Mazda R-2 Mercon 3.8 Qts. (3.6L)
ZF S5-42 Mercon 3.4 Qts. (3.2L)
Transfer Case (Warner 13-56) Mercon 2.0 Qts. (1.9L)
Van
AOD Auto. Mercon 12.3 Qts. (11.6L)
C-6 Auto. Mercon 12.0 Qts. (11.4L)
E4OD Auto. Mercon 15.7 Qts. (14.8L)
5-Speed Overdrive (ZF HD) Mercon 3.4 Qts. (3.2L)
AXLE CAPACITIES

Application Pts. (L)
Bronco
Front 3.8 (1.80)
Rear (8.8" Ford (1) ) (2) 5.5 (2.60)
Pickup
Front
Dana 44-IFS L.D. 3.6 (1.70)
Dana 50-IFS H.D. 3.8 (1.80)
Dana 60 Monobeam 5.8 (2.80)
Rear
8.8" Ford 5.5 (2.60)
10.25" Ford (3) 7.5 (3.50)
11.25" Dana 80 8.3 (3.90)
Van (Rear)
8.8" Ford (1) (2) 5.5 (2.60)
9.75" Dana M60-1U 6.3 (3.00)
10.5" Dana M70-2U 6.6 (3.10)
10.5" Dana M70-1HD 7.4 (3.50)
(1) Conventional and Traction-Lok.
(2) Add 4 oz. friction modifier for Traction-Lok axles.
(3) Conventional and Traction-Lok, Semi and Full Float.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.