Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1990 Ford Probe V6-182 3.0LFACTORY OEM SERVICE PROCEDURE
Computers and Control Systems: Technical Service Bulletins
- Recalls
- Customer Interest
- By Symptom
- All Technical Service Bulletins
- Electrical/Electronic/Fuel Induction - Glossary
- Electronics - Diagnostic Tools and Adapter Application
- EEC IV Quick Test - Code 41/173 Stored In Memory
- IDM and Spark Timing Diagnosis - Manual Revision
- Three Digit Self Test Codes - Service Tip
- Electronic Modules - Protection From Static Electricity
- Engine - Rough Idle During Warm Up
- Engine Control Systems - Diagnosis Revision
- Overview
- Diagnosis Routines, Improper Shift
- Bypass Air Control System
- Fuel System Delivery/Diagnosis and Testing
- Ignition System and Timing Procedures
- EEC Quick Test - All Engines
- EEC Pinpoint Test - All Engines
- Index
- Pinpoint Test Instructions
- Barometric Pressure Switch
- Clutch Cycling Pressure Switch 2.2L All
- Cylinder Identification 1.6L, 1.8L
- Cylinder Identification 2.2L Turbo
- Crankshaft Position 1.3L, 1.8L and 2.2L Turbo
- Daytime Running Lamps 1.3L, 1.8L and 2.0L Turbo (Canada Only)
- Engine Coolant Temperature - All Engines
- Electrical Load Control Unit 1.6L and Turbo
- EGR Valve Position 2.2L Turbo and Non-Turbo Calif.
- Ignition Diagnostic Monitor - All Engines
- MIL and Overboost Indicator Warning - All Engines
- Knock Control 1.6L Turbo
- Knock Control 2.2L Turbo
- Power and Ground Connections - All Engines
- Relay Output Check - All Engines
- Solenoid Controlled By Ground - All Engines
- Switch Monitor Lamp - All Vehicles
- Switch to Ground - All Engines
- Self Test Input - All Engines
- Self Test Output - All Engines
- Switch to Power - All Engines
- Throttle Position 1.6L, 1.8L, 2.2L All
- Vane Air Flow - All Engines
- Vane Air Temperature - All Engines
- Vehicle Power - All Engines
- Reference Voltage - All Engines
- EEC-IV Monitor Intermittent Fault Diagnostics
- 4EAT Transaxle
- Quick Test
- Test Equipment
- Pinpoint Test
- Input/Output Sensors
- Pinpoint Test Instructions
- Downshift Signal 2.2L Turbo 4EAT, 1.8L 4EAT
- Manual Shift Lamp 3.0L, 2.2L and 1.6L
- Power and Ground Connections All 4EAT
- Solenoid Controlled By Power - All 4EAT
- Self Test Input All 4EAT Except 1.8L and 1.9L
- Self Test Output - All 4EAT
- Switch to Ground - All 4EAT
- Switch to Power - All 4EAT
- Throttle Position - All 4EAT
- Torque Converter Speed Pulse Generator - All 4EAT
- Transaxle Oil Temperature 1.8L, 1.9L 4EAT
- Transaxle Oil Temperature Switch 2.2L, 3.0L, 1.6L - 4EAT
- Vehicle Power - All 4EAT
- Vehicle Speed - All 4EAT
- Reference Voltage - All 4EAT
- Electronic Steering/Ride Control Test - Revision
- Recall - Throttle Position Sensor Replacement
- High Cold Idle RPM After Recall 91E08 Performed
- Recall - EEC Processor Replacement
- EGO Sensors - Silicone Contamination
- A/T Manual Shift Light - Intermittent Display
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
