Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1988 Ford Pickup F350, 2D Pickup, 7.3 M, RWD, AutomaticFACTORY OEM SERVICE PROCEDURE
Service Code Definitions
SERVICE CODE DEFINITIONS
| Codes | Definition |
|---|---|
| 11 | System "Passes" test procedure |
| 12 | Idle RPM not within specifications |
| 13 | Idle Speed Control (ISC) RPM too high |
| 14 | Erratic ignition signal from PIP |
| 15 | Power interrupted to Keep Alive Memory (KAM), Pin No. 1 |
| 16 | Idle Speed Control (ISC) RPM too high or throttle pedal touched during KOER SELF-TEST |
| 17 | Idle Speed Control (ISC) RPM too low |
| 18 | Spark timing incorrect |
| 19 | Idle Speed Control (ISC) RPM too low |
| 21 | Engine Coolant Temperature (ECT) sensor/signal out of range |
| 22 | Manifold Absolute Pressure (MAP) sensor/signal out of range |
| 23 | Throttle Position Sensor (TPS) signal/out of range |
| 24 | Air Charge Temperature (ACT) sensor/signal out of range |
| 25 | Knock sensor signal not received by ECA |
| 26 | Mass Air Flow sensor (MAF) signal out of range |
| 27 | Vehicle Speed Sensor (VSS) signal not received (2.3L Turbo MPFI) |
| 28 | Ambient temperature less than 50Β°F (10Β°C) |
| 29 | Vehicle Speed Sensor (VSS) not functioning |
| 31 | Pressure Feedback EGR (PFE) circuit open |
| 32 | EGR Control solenoid (EGRC) or EGR Vent solenoid (EGRV) signal failure |
| 33 | EGR valve not operating or sticking |
| 34 | EGR Control solenoid (EGRC) or EGR Vent solenoid (EGRV) signal failure |
| 35 | RPM too low for EGR testing or Pressure Feedback EGR (PFE) circuit short |
| 38 | Idle Tracking Switch (ITS) sticking or open in signal circuit |
| 39 | Converter by-pass clutch not operating correctly |
| 41 | Heated Exhaust Gas Oxygen (HEGO) sensor, lean signal in closed loop. (On 5.0L MA SEFI, indicates RH sensor) |
| 42 | Heated Exhaust Gas Oxygen (HEGO) sensor signal rich in closed loop. Excessive fuel pressure or volume (On 5.0L MA SEFI, indicates RH sensor) |
| 43 | Heated Exhaust Gas Oxygen (HEGO) sensor signal lean during WOT test |
| 44 | Air management system (TAB/TAD solenoids) |
| 45 | Thermactor Air Diverter (TAD) system operation |
| 46 | Thermactor Air By-pass (TAB) system operation |
| 47 | Idle speed control (by-pass Air), low flow of unmetered air |
| 48 | Idle speed control (by-pass Air), high flow of unmetered air |
| 51 | Engine Coolant Temperature (ECT) sensor, signal circuit open |
| 52 | Power Steering Pressure Switch (PSPS) open/shorted, steering wheel not turned during KOER SELF-TEST |
| 53 | Throttle Position Sensor (TPS) signal circuit short |
| 54 | Air Charge Temperature (ACT) sensor circuit open |
| 55 | Key power check circuit open (CFI engines) |
| 56 | Vane Airflow (VAF) sensor or Mass Air Flow (MAF) sensor, shorted VREF to SIG circuit |
| 57 | Neutral Pressure Switch (NPS) failed in neutral |
| 58 | Vane Air Temperature (VAT) sensor circuit open |
| 59 | Transmission Hydraulic Switch (THS), 4/3 pressure switch, failed in open position |
| 61 | Engine Coolant Temp. (ECT) sensor, signal circuit short |
| 62 | Transmission Hydraulic Switch (THS) 4/3 pressure switch failed in closed position |
| 63 | Throttle Position Sensor (TPS) signal circuit open |
| 64 | Air Charge Temperature (ACT) sensor circuit short |
| 65 | Did not go to closed loop fuel control on HEGO switching. Faulty HEGO signal |
| 66 | Vane Airflow (VAF) sensor or Mass Air Flow (MAF) sensor, shorted SIG to SIG RTN circuit |
| 67 | Neutral Drive Switch (NDS), A/C Input, Neutral Pressure Switch (NPS) signal interrupted |
| 68 | Vane Air Temperature (VAT) sensor circuit short |
| 69 | Transmission Hydraulic Switch (THS) 3/2 pressure switch failed in closed position |
| 71 | Idle Tracking Switch (ITS) shorted to ground or stuck closed |
| 72 | Fault in VPWR circuit to EEC power relay |
| 73 | Throttle Position Sensor (TPS) did not rotate more than 25% during dynamic response test |
| 74 | Brake On/Off (BOO) switch always open or not applied during KOER SELF-TEST |
| 75 | Brake On/Off (BOO) switch always closed, or signal circuit shorted |
| 76 | Vane Airflow (VAF) sensor, no voltage signal increase during Dynamic Response Test |
| 77 | ECA request for Dynamic Response Test |
| 78 | Power supply circuit to EEC power relay interrupted |
| 79 | Neutral Drive Switch (NDS), A/C Input, Neutral Position Switch (NPS) signal interrupted |
| 81 | Open or shorted signal from turbo boost solenoid |
| 82 | Integrated Controller Relay Module (ICRM), electric fan processor signal shorted to ground or open |
| 83 | Integrated Controller Relay Module (ICRM), high speed electric fan processor signal shorted to ground or open |
| 84 | EGR Valve Regulator (EVR) resistance signal out of range |
| 85 | Fuel mixture made leaner (Adaptive Fuel) to accommodate canister purge function or excessive fuel pressure or volume |
| 86 | Fuel mixture made richer (Adaptive Fuel) due to low fuel pressure or low volume |
| 87 | Open in fuel pump circuit or VPWR circuit between EEC power relay and fuel pump relay |
| 88 | Integrated Controller Relay Module (ICRM), electric fan processor signal shorted to ground or open |
| 89 | Converter by-pass clutch solenoid always open or closed |
| 91 | Heated Exhaust Gas Oxygen (HEGO) sensor, lean signal in closed loop (on 5.0L MA SEFI, indicates LH sensor) |
| 92 | Heated Exhaust Gas Oxygen (HEGO) sensor signal rich in closed loop; excessive fuel pressure or volume (on 5.0L MA SEFI, indicates LH sensor) |
| 93 | Throttle linkage, DC motor idle speed control/idle tracking switch and Throttle Position Sensor (TPS) (1.9L & 2.5L CFI) |
| 94 | Air management system (TAB/TAD solenoids) |
| 95 | Inertia switch or fuel pump circuit shorted or open |
| 96 | No power to fuel pump relay |
| 98 | Vehicle did not pass KOEO SELF-TEST. Code 11 necessary to proceed with KOER test |
| 99 | ECA has not stored enough information to control idle speed |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
