1974 Ford Courier Automatic TransFACTORY OEM SERVICE PROCEDURE

Ignition Distributors

NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1965 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No.(2) Rot (1) Automatic Advance (Distr. Degrees & RPM) Vacuum Advance (Distr. Deg. & In. of Hg.)
Deg. RPM Deg. RPM Deg. RPM Deg. In. Hg. Deg. In. Hg.
C5TF-B (3)(5) CC 0-1 500 2-3 700 4.75-5.75 1200 .5-3.5 6 6-9 12
C5TF-C (3)(5) CC 0-1 500 2-3 700 4.75-5.75 1200 .5-3.5 6 6-9 12
C5TF-K (3) C .75-1.75 600 8.25-9.25 1200 11-12.5 2000 1-4 8 6.5-8.5 14
C5TF-L (3) C 0-1 600 7-8 1200 11-12.5 2000 1-4 8 4-7 12
C5TF-N (4) C 0 500 2.5-3.5 800 9.5-10.75 2000 0 .38 9.5-10.75 5.20
C5TF-R (4) C 1.5-2.5 800 5.25-6.25 1200 8.5-9.75 2000 0 .30 8.5-9.75 3.50
C5TF-Y (3) CC 1.75-2.75 600 5.5-6.5 800 12.5-14 2000 2-5 8 7-10 15
C5TF-Z (3) CC 1.75-2.75 450 7.75-8.75 1200 10.5-12 2000 2-5 8 6.5-9.5 14
C5UF-G (4) C 1-2 600 4.5-5.5 800 8.25-9.5 1200 1-2 .70 8.25-9.5 2.10
C5UF-J (4) C .25-1.25 600 7-8 1200 11-12.25 2000 .25-1.25 .45 7-8 1.75
C5UF-K (4) C 1-2 500 3-4.25 800 9.5-10.75 2000 1-2 .35 6.25-7.25 1.80
C5AF-AD (4) C 1-2 600 4.5-5.5 800 8.25-9.5 1200 1-2 .70 8.25-9.5 2.10
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.
(2) Basic number is 12127. Table gives prefix and suffix only.
(3) Ford Dual Advance Distributor.
(4) Ford Loadomatic Distributor.
(5) Transistor Ignition.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1966 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. (2) Rot (1) Automatic Advance (Distr. Degrees & RPM) Vacuum Advance (Distr. Deg. & In. of Hg.)
Deg. RPM Deg. RPM Deg. RPM Deg. In. Hg. Deg. In. Hg.
C5AF-B (3) CC 4.5-5.5 550 7.75-8.75 1200 10.5-12 2000 2-5 8 6.5-9.5 14
C5TF-A (3) CC 5.5-6.5 800 9.75-10.75 1400 12.25-14 2000 2-5 8 7-10 15
C5TF-AB (3)(5) CC 2-3 800 8-9.25 1500 9.25-10.75 2000 1.75-4.5 8 5.5-8.5 15
C5UF-J (4) C .25-1.25 600 7-8 1200 11-12.5 2000 3.5-4.5 .75 7-8 1.75
C6AF-Y (4) C 1-2 800 4.5-5.5 1200 8.75-10 2000 1-2 .90 7-8.25 3.6
C6AF-AA (3) C 1.25-2.25 600 7.25-8.5 1200 11.5-13 2000 3-6 7 9.5-12.5 14
C6AF-AD (3) C 0-.5 300 5.75-6.75 1000 9.5-11 2000 0-1 4 8.5-11.5 15
C6TF-G (3)(5) CC 2.5-3.75 650 8.25-9.25 1100 11.5-13 1800 2-5 7 7-10 15
C6TF-H (3) CC .5-1.5 400 6.25-7.25 800 9.75-11.25 1800 1-4 7 7-10 15
C6TF-AA (3)(5) CC .75-1.75 500 11.5-12.5 1800 12.5-14 2000 0-1 5 7-10 15
C6TF-AB (3) CC .75-1.75 500 6.75-8 1200 12.5-14 2000 0-1 5 7-10 15
C6TF-AC (4) C 4.5-5.5 800 9.25-10.5 1600 10.25-11.75 2000 4.5-5.5 1.2 9.25-10.5 3.70
C6TF-AD (3) C 0-1 600 4-5.25 900 8.5-10 2000 1-4 8 5.5-8.5 13
C6TF-AF (3) C .75-1.75 600 8.25-9.25 1200 12.5-14 2000 1-4 8 6.5-8.5 14
C6TF-AG (3) C 0-1 600 7-8 1200 11-12.5 2000 1-4 8 4-7 12
C6TF-AH (3) C 0-1 600 6-7.25 1200 8.5-10 2000 1-4 6 7-10 12
C6TF-AJ (3) C 1-2 500 8.5-9.5 1100 9-11 2000 1-4 6 7-10 12
C6TF-AM (4)(5) C 1-2 600 7.5-8.5 1200 10.5-11.75 2000 1-2 0.7 7.5-8.5 2.10
C6TF-AN (4)(5) C 1-2 800 4.5-5.5 1200 8.75-10 2000 1-2 0.9 7-8.75 3.60
C6TF-AR (3)(5) C 0-1 600 6-7.25 1200 8.25-10 2000 1-4 8 5.5-8.5 13
C6TF-AS (3)(5) C .75-1.75 600 8.25-9.25 1200 12.5-14 2000 1-4 8 6.5-8.5 14
C6TF-AT (3)(5) C 0-1 600 7-8 1200 11-12.5 2000 1-4 8 4-7 12
C6TF-AU (3)(5) C 0-1 600 6-7.25 1200 8.5-10 2000 1-4 6 7-10 12
C6TF-AV (3)(5) C 1-2 500 8.5-9.5 1100 9-11 2000 1-4 6 7-10 12
C6TF-AY (3) C 0-.5 350 3.5-4.5 1050 8-9.5 1900 0-1 4 9-12 17
C6TF-BA(3) C 0-.5 300 6-7 1000 10.25-11.75 2000 0-1 4 9.25-12.5 15
C6TF-BD (3)(5) C 0-.5 300 5.75-6.75 1000 9.5-11 2000 0-1 4 8.5-11.5 15
C6TF-BE (3)(5) C 0-.5 300 6-7 1000 10.5-11.75 2000 0-1 4 9.25-12.5 15
C6TF-BC (3)(5) C 0-.5 300 3.25-4.25 1000 7.5-8.75 1800 0-1 4 8.5-11.5 15
C6UF-F (3) C 1-2 600 4.25-5.5 1200 8-9.5 1900 0-1 4 9-12 17
C6UF-H (3) C 0-.5 300 5-6 700 7.5-9 1600 0-1 4 9-12 17
C7OF-A (3) CC 0-.5 400 7.5-8.5 1000 12-13.75 2000 0-1 5 7.25-10.25 15
C7OF-B (3) CC 0-.5 300 7.75-8.75 1000 10.5-12 2000 0-1 5 9.25-12.25 15
C7OF-D (3) CC 0-.5 300 8-9 1000 12.5-14 2000 0-1 5 9.5-12.5 15
C7OF-E (3) CC 0-.5 300 8.5-9.75 1000 12.25-13.75 2000 0-1 5 8.5-11.5 15
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.
(2) Basic number is 12127. Table gives prefix and suffix only.
(3) Ford Dual Advance Distributor.
(4) Ford Loadomatic Distributor.
(5) Transistor Ignition.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1967 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. Rot (1) Automatic Advance (Distr. Degrees & RPM) Vacuum Advance (Distr. Deg. & In. of Hg.)
Deg. RPM Deg. RPM Deg. RPM Deg. In. Hg. Deg. In. Hg.
C5DF-C(4) C 2.5-3.5 800 6.5-7.5 1200 10.25-11.5 2000 2.5-3.5 0.80 8.75-10 3.0
C5DF-K(4) C .75-1.75 800 3.75-4.75 1200 7-8.25 2000 .75-1.75 0.79 5.75-7 3.0
C5UF-J(4) C .25-1.25 600 7-8 1200 11-12.25 2000 .25-1.25 0.45 7-8 1.75
C5UF-K(4) C 1-2 500 6.25-7.25 1200 9.5-10.75 2000 1-2 0.35 6.5-7.25 1.80
C6AF-Y(4) C 1-2 800 4.5-5.5 1200 8.75-10 2000 1-2 0.90 7-8.25 3.60
C6AF-AD(3) C 2.25-3.25 500 5.75-6.75 1000 7.5-9 1500 0-1 4 8.5-11.5 15
C6TF-AC(4) C 4.25-5.5 800 7.5-8.75 1200 10.25-11.75 2000 4.25-5.5 1.20 9.25-10.5 3.70
C6TF-AF(3) C .75-1.75 600 8.25-9.25 1200 12.5-14 2000 1-4 8 6.5-8.5 14
C6TF-AG(3) C 0-1 600 7-8 1200 11-12.5 2000 1-4 8 4-7 12
C6TF-AY(3) C 1-2 600 4.25-5.5 1200 8-9.5 1900 0-1 4 9-12 17
C6TF-BA(3) C 2.25-3.25 500 7.25-8.5 1300 10.25-11.75 2000 0-4 6 9.5-12.5 15
C6UF-F(4) C 4.25-5.25 800 7.75-9 1200 10-11.75 1600 4.25-5.25 0.85 10-11.25 3.70
C6UF-H(3) C 3-4 525 5-6 700 7.5-9 1600 0-1 4 9-12 17
C7DF-A(3) C 2-3 500 8.75-10 1300 12.5-14 2000 0-1 5 4-7 15
C7OF-A(3) CC 4.75-5.75 800 9.75-11 1500 12-13.75 2000 0-1 5 7.25-10.25 15
C7OF-D(3) CC 3-4 600 8-9 1000 12.5-14 2000 0-1 5 9.5-12.5 15
C7TF-A(3) CC .75-1.75 500 9-10.25 1500 12.25-14 2000 0-1 5 7-10.25 15
C7TF-D(3) C 1-2 600 3.75-5 1000 8-9.25 2000 0-1 4 6-9 15
C7TF-F(3) CC 3.25-4.25 500 7-8 1000 10.5-12 2000 0-1 5 7-10 15
C7TF-J(3) CC 1-2 800 8-9 1400 11-12.5 2000 0-1 5 4-7 15
C7TF-R(3) CC 5.5-6.5 1000 10.5-11.75 1500 13.5-14.75 2000 0-1 5 7-10 15
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.
(2) Basic number is 12127. Table gives prefix and suffix only.
(3) Ford Dual Advance Distributor.
(4) Ford Loadomatic Distributor.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1968 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. (2) Rot (1) Automatic Advance (Distr. Degrees & RPM) Vacuum Advance (Distr. Deg. & In. of Hg.)
Deg. RPM Deg. RPM Deg. RPM Deg. In. Hg. Deg. In. Hg.
C5DF-C (4) C 2.5-3.5 800 6.5-7.5 1200 10.25-11.5 2000 0-.5 0.3 6.5-7.5 1.8
C6AF-Y (4) C 1-2 800 4.5-5.5 1200 8.75-10 2000 1-2 .90 7-8.25 3.6
C6TF-AC (4) C 4.5-5.5 800 9.25-10.5 1600 10.25-11.75 2000 4.5-5.5 1.2 9.25-10.5 3.70
C6TF-AD (3) C 0-1 600 4-5.25 900 8.5-10 2000 1-4 8 5.5-8.5 13
C6TF-AF (3) C .75-1.75 600 8.25-9.25 1200 12.5-14 2000 1-4 8 6.5-8.5 14
C6TF-AG (3) C 0-1 600 7-8 1200 11-12.5 2000 1-4 8 4-7 12
C8AF-A (3) C 0-.5 500 2.25-4.5 1000 7.5-10 2000 0-.75 5 5.5-8 15
C8TF-D (3) C 0-1 500 1.75-4 1000 6.5-9 2000 0-1 5 10-12.5 15
C8TF-F (3) CC 0-.5 500 3.5-5.5 1000 8.75-11 2000 0-1 5 5.75-8.75 15
C8TF-G (3) CC 1.5-3.75 500 6.5-8.75 1000 12-14.5 2000 0-1 5 10-12.5 15
C8TF-H (3) CC 1.5-3.5 500 6.5-8.75 1000 12-14.5 2000 0-1 5 9.75-12.5 15
C8TF-L (3) CC 0-2 500 4.25-6.5 1000 12-14.5 2000 0-1 5 9.75-12.5 15
C8UF-D (3) C 0-.5 500 3.75-5.75 1000 7.5-10 2000 0-1 5 6.25-9 15
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.
(2) Basic number is 12127. Table gives prefix and suffix only.
(3) Ford Dual Advance Distributor.
(4) Ford Loadomatic Distributor.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1969 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. Rot (1) Automatic Advance (Distr. Degrees & RPM) Vacuum Advance (Distr. Deg. & In. of Hg.)
Deg. RPM Deg. RPM Deg. RPM Deg. In. Hg. Deg. In. Hg.
C6AF-Y(3) C .75-2 800 4.5-5.5 1200 8.75-10 2000 0-.5 .34 4.5-5.5 2.1
C6TF-AC(2) C 4.75-5.5 800 7.5-8.75 1200 10.25-11.75 2000 0-.5 .4 7.5-8.75 2.1
C6TF-AD(2) C 0-.5 500 4.5-6.5 1000 7.5-10 2000 0-1 5 6-8.5 15
C6TF-AF(2) C 0-.5 500 6-8.25 1000 11.5-14 2000 0-1 5 5.5-8.5 15
C6TF-AG(2) C 0-.5 500 4.5-6.5 1000 10-12.5 2000 0-1 5 4-7 15
C7OF-A(2) CC 0-.5 500 6.5-8.5 1000 11.25-13.75 2000 0-1 5 7.25-10.25 15
C7OF-B(2) CC 1.75-3.75 500 6.75-8.75 1000 9.5-12 2000 0-1 5 9.5-12.25 15
C8AF-A(2) C 0-.5 500 2.25-4.5 1000 7.5-10 2000 0-.75 5 5.5-8 15
C8TF-D(2) C 0-1 500 1.75-4 1000 6.5-9 2000 0-1 5 10-12.5 15
C8TF-F(2) CC 0-.5 500 3.5-5.5 1000 8.75-11 2000 0-1 5 5.75-8.75 15
C8TF-H(2) CC 1.5-3.5 500 6.5-8.75 1000 12-14.5 2000 0-1 5 9.75-12.5 15
C8TF-U(2) C 0-.5 500 4.5-6.5 1000 7.5-10 2000 0-1.5 5 8.75-11.75 15
C9TF-J(2) C 0-1 500 1.75-4 1000 6.5-9 2000 0-1 5 10-12.5 15
C9UF-A(2) C 0-.5 500 2.25-4.5 1000 7.5-10 2000 0.75 5 5.5-8 15
C9UF-C(2) CC 0-.5 500 3.25-5.25 1000 9.75-12.25 2000 0-.75 5 3.75-7 15
C9UF-F(2) C 0-.5 500 3.5-5.5 1000 9.5-12 2000 0-.75 5 2.75-6 15
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.

(2) - Basic number is 12127. Table gives prefix and suffix only.
(2) Ford Dual Advance Distributor.
(3) Ford Loadomatic Distributor.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1970 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. (2) Rot. (1) Automatic Advance (Distr. Degrees @ RPM) Vacuum Advance (Distr. Degrees) Operate Distr. @ 1000 RPM Vacuum Retard (Distr. Degrees) Operate Distr. @ 1000 RPM
500 750 1000 1500 2000 5 10 15 20 5 10 15 20
C8AF-A (3) C 0-.5 0-1.5 2.25-4.5 6-8 7.5-10 0-.75 .75-3.75 5.5-8 5.5-8 0-1.5 2.5-6 5-6 5-6
C8DF-A (3) C 0-2 6.25-8.25 6.75-11 10.5-13 ..... 0-1 3-6 5.5-8 5.5-8 0-1.75 3.5-6 5-6 5-6
C8TF-D (3) C 0-1 .75-2.75 1.75-4 4.25-6.5 6.5-9 0-1 6.75-9.75 10-12.5 10-12.5 0-1.25 2.75-6 5-6 5-6
C8TF-F (3) CC 0-.5 0-2 3.5-5.5 7-9 8.75-11 0-1 2-5 5.75-8.75 8-11 0-1.75 3.5-6 5-6 5-6
C8TF-U (4) C 0-.5 .75-3 4.5-6.5 6-8.25 7.5-10 0-1.5 5.75-875 8.75-11.25 10-12.5 ..... ..... ..... .....
C9UF-A (4) C 0-.5 0-1.5 2.25-4.5 5.75-8 7.5-10 0-.75 .75-3.75 5.5-8 5.5-8 ..... ..... ..... .....
C9UF-F (3) C 0-.5 0-2 3.5-5.5 7.75-10 9.5-12 0-.75 0-2 2.75-6 3.5-6 0-.25 1.25-5.75 5-6 5-6
DOTF-G (4) CC 0-.5 2.5-4.5 5-7 6.5-8.75 8-10.5 0-.75 0-1.75 3.75-7 5.5-8 ..... ..... ..... .....
DOTF-H (3) CC 0-.5 2.5-4.5 5-7 6.5-8.75 8-10.5 0-.75 0-1.5 3.75-7 5.5-8 0-3.25 4.75-6 5-6 5-6
DOTF-J (3) CC 2.5-4.5 7.75-9.75 9-11 11.25-13.5 13.75-16.25 0-1.25 6.5-9 6.5-9 6.5-9 0-.25 2-6 5-6 5-6
DOTF-K (4) CC 2.5-4.5 7.75-9.75 9-11 11.25-13.5 13.75-16.25 0-1.25 6-9 6.5-9 6.5-9 ..... ..... ..... .....
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.
(2) Basic number is 12127. Table gives prefix and suffix only.
(3) Dual Vacuum Diaphragm Distributor.
(4) Single Vacuum Diaphragm Distributor.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1971 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. Rot. (1) Automatic Advance (Distr. Degrees @ RPM) Vacuum Advance (Distr. Degrees) Operate Distr. @ 1000 RPM Vacuum Retard (Distr. Degrees) Operate Distr. @ 1000 RPM
500 750 1000 1500 2000 5 10 15 20 5 10 15 20
C8AF-A(2) C 0-.5 0-1.5 2.25-4.5 6-8 7.5-10 0-.75 .75-3.75 5.5-8 5.5-8 0-1.5 2.5-6 5-7 5-7
C8DF-A(2) C 0-2 6.25-8.25 6.75-11 4.25-6.5 6.5-9 0-1 3-6 5.5-8 5.5-8 0-1.75 3.5-6 5-6 5-6
C8TF-D(2) C 0-1 .75-2.75 1.75-4 4.25-6.5 6.5-9 0-1 6.75-9.75 10-12.5 10-12.5 0-1.25 2.75-6 5-7 5-7
C8TF-U(3) C 0.5 .75-3 4.5-6.5 6-8.25 7.5-10 0-1.5 5.75-8.75 8.75-11.75 10-12.5 ..... ..... ..... .....
C9UF-A(3) C 0-.5 0-1.5 2.25-4.5 6-8 7.5-10 0-.75 .75-3.75 5.5-8 5.5-8 ..... ..... ..... .....
C9UF-F(2) C 0-.5 0-2 3.5-5.5 7.75-10 9.5-12 0-.75 0-2 2.75-6 3.5-6 0-.25 1.25-6.25 5-7 5-7
DOTF-J(2) CC 2.5-4.5 7.75-9.75 9-11 11.25-13.5 13.75-16.25 0-1.25 6.5-9 6.5-9 6.5-9 0-.25 2-7 5-7 5-7
DOTF-M(2) CC 0-.5 .5-2.5 6-8 8.5-10.75 9.75-12.25 0-.75 0-2.25 5-8 8-10.5 0-3 4.5-7 5-7 5-7
D1TF-CA(2) C 0-.5 0-.5 .5-2.5 5.75-8 7.75-10.25 0-1 1-4 5.5-8 5.5-8 0-1.25 2.5-7 5-7 5-7
D1TF-EA(3) CC 0-.75 2.5-5.75 9-11 11.25-13.5 13.5-16 0-1.25 6-9 6.5-9 6.5-9 ..... ..... ..... .....
D1UF-A(3) CC 0.5 .5-2.5 6-8 8.5-10.75 9.75-12.25 0-1 0-2.25 5-8 8-10.5 ..... ..... ..... .....
(1) C(Clockwise) CC(Counterclockwise) viewed from rotor end.

(2) - Basic number is 12127. Table gives prefix and suffix only.
(2) Dual Vacuum Diaphragm Distributor.
(3) Single Vacuum Diaphragm Distributor.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1972 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. Rot. (1) Automatic Advance (Distr. Degrees @ RPM) Vacuum Advance (Distr. Degrees) Operate Distr. 1000 RPM Vacuum Retard (Distr. Degrees) Operate Distr. @ 1000 RPM
500 750 1000 1500 2000 5 10 15 20 5 10 15 20
D2AF-CA(2) CC 0-.5 0-1.5 4.5-6.5 7.5-9.5 8.5-11 0-1.25 2.5-5.5 2.5-5.5 2.5-5.5 0-2.25 3.25-7 5-7 5-7
D2AF-DA(2) CC 0-.5 0-1.5 4.5-6.5 7.5-9.5 8.5-11 0-1.25 2.5-5.5 2.5-5.5 2.5-5.5 0-2.25 3.25-7 5-7 5-7
D2BF-AA(2) C 0-1 0-2 3.5-5.5 8-10 9.5-12 0-1 0-2.5 3.5-6.5 4.5-7.5 0-2.5 3.5-6.5 5-7 5-7
D2TF-AA(2) CC 1.5-4.5 7.5-10 9-11.25 11.25-13.5 13.5-16 0-1.5 6.25-9.25 6.25-9.25 6.25-9.25 0-6.5 5-7 5-7 5-7
D2TF-EA(3) C 0-.5 1-3 4.5-6.5. 6-8.25 7.5-10 0-2.5 6-9 10.5-13.5 10.5-13.5 ..... ..... ..... .....
D2TF-KA(2) CC 1.5-4.5 7.5-10 9-11.25 11.25-13.5 13.5-16 0-1.5 6.25-9.25 6.25-9.25 6.25-9.25 0-6.5 5-7 5-7 5-7
D2TF-LB(3) CC 0-1 2.5-6 9-11.25 11.25-13.5 13.5-16 0-1 1.5-4.5 6.5-9.25 6.5-9.25 ..... ..... ..... .....
D2TF-PA(2) CC 0-1 2.56 9-11.25 11.25-13.5 13.5-16 0-1 1.5-4.5 6.5-9.25 6.5-9.25 0-6.5 5-7 5-7 5-7
D2UF-AA(2) C 0-.5 0-1.5 2.25-4.5 6-8 7.5-10 0-1 1-4 4.5-7.5 4.5-7.5 0-2.5 3.5-6.5 5-7 5-7
D2UF-CA(3) C 0-.5 0-1.5 2.25-4.5 6-8 7.5-10 0-1 1-4 5.5-8.5 6.5-9.5 ..... ..... ..... .....
D2UF-DA(2) C 0-.5 0-1.5 2.25-4.5 6-8 7.5-10 0-1 1-4 4.5-7.5 4.5-7.5 0-4.5 5-7 5-7 5-7
D2UF-EA(2) CC 0-1 0-2.5 6-8 8.5-11 9.5-12.5 0-1 0-2 5.5-8.5 8.5-11.5 0-3 4-7 5-7 5-7
D2UF-GA(2) CC 0-1 0-2.5 6-8 8.5-11 9.5-12.5 0-1 0-2 5.5-8.5 8.5-11.5 0-3 4-7 5-7 5-7
D2UF-LA(2) CC 0-1.25 2.5-5 6-8 7.5-9.5 8.5-10.5 0-1.25 2.5-5.5 2.5-5.5 2.5-5.5 0-2.25 3.5-7 5-7 5-7
D2UF-MA(2) CC 0-.5 2.5-4.5 6.5-8.5 8.5-11.5 9.5-12 0-1 0-2 5.5-8.5 8.5-11.5 0-3 4-7 5-7 5-7
(1) C(Clockwise). CC(Counterclockwise) Viewed from rotor end.

(2) - Basic number is 12127. Table gives prefix and suffix only.
(2) Dual Vacuum Diaphragm Distributor.
(3) Single Vacuum Diaphragm Distributor.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1973 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Port No. (2) Rot. (1) Automatic Advance (Distr. Degrees @ RPM) Vacuum Advance (Distr. Degrees) Operate Distr. @ 1000 RPM Vacuum Retard (Distr. Degrees) Operate Distr. @ 1000 RPM
500 750 1000 1500 2000 5 10 15 20 5 10 15 20
D3BF-AA (3) C 0-1.5 3.5-5.5 7.5-9.5 9.5-11.5 10.5-12.5 0-3.5 4.5-7.25 4.5-7.25 4.5-7.25 0-3.5 2-4 2-4 2-4
D3BF-BA (3) CC 0-1 2.5-4.5 6.5-8.5 8.5-11 9.5-12 0-1 0-2 5.5-8.5 8.5-11.5 0-3.5 4.5-7 5-7 5-7
D3BF-CA (3) C 0-1.5 3.5-5.5 7.5-9.5 9.5-11.5 10.5-12.5 0-3.5 4.5-7.25 4.5-7.25 4.5-7.25 0-3.5 2-4 2-4 2-4
D3BF-DA (3) CC 0-1.25 2.5-4.5 5.5-7.5 8.5-10.5 11.5-13.5 0-1 0-2 5.5-8.5 8.5-11.5 0-3.5 5-7 5-7 5-7
D3TF-EA (4) CC 0-1.5 4.5-6.5 6.8 8-10.5 10-12.5 0-1.25 5.5-8.5 6.5-9.25 6.5-9.25 ..... ..... ..... .....
D3TF-GA (4) C 0-1 .5-2.5 2.5-4.5 4-6 5.25-7.5 0-1.25 5-8 6.5-9.25 6.5-9.25 ..... ..... ..... .....
D3TF-HA (4) CC 0-1.25 6-8 8-10 11.5-14 11.5-14 0-1 0-1.5 4-7 4.5-7.25 ..... ..... ..... .....
D3TF-PA (4) CC 0-1.5 4.5-6.5 8-10 11.5-13.5 15-17.5 0-2.5 5.5-8.5 6.5-9.25 6.5-9.25 ..... ..... ..... .....
D3TF-UA (3) CC 0-1.5 4.5-6.5 8-10 11.5-13.5 15-17.5 0-1.5 6.5-9.25 6.5-9.25 6.5-9.25 0-3.5 5-7 5-7 5-7
D3TF-VA (4) CC 0-1 4.5-6.5 8-10 10.5-12.5 13-15.25 0-2.5 6-9 9.5-12.5 13-15.25 ..... ..... ..... .....
D3TF-XA (4) CC 0-1 4.5-6.5 8-10 10.5-12.5 13-15.25 0-2.5 6-9 9.5-12.5 13-15.25 ..... ..... ..... .....
D3UF-AA (3) C 0-.5 0-2 5-7 7-9 8.25-10.5 0-1.5 6.25-9.25 8.5-11.5 8.5-11.25 0-4.25 5-7 5-7 5-7
D3UF-BA (3) C 0-.5 0-1.5 2.5-4.5 6-8 7.5-10 0-1 1-4.5 4.5-7.25 4.5-7.25 0-3.25 4.5-7 5-7 5-7
D3UF-EA (3) CC 0-1.25 2.5-4.5 5.5-7.5 9-11 12.25-14.5 0-1.5 6.5-9.25 6.5-9.25 6.5-9.25 0-4 5-7 5-7 5-7
D3UF-GA (3) CC 0-1 0-2.5 2-4.5 5.5-8.25 9.25-11.5 0-.5 0-2.5 2.5-5.25 2.5-5.25 0-3 2-4 2-4 2-4
D3UF-HA (4) CC 0-1 2.5-4.5 5-7 6.5-9 8.25-10.5 0-1 0-1.5 4-7 4.5-7.25 ..... ..... ..... .....
D3UF-JA (3) CC 0-1.5 2.5-4.5 5-7 6.5-9 8.25-10.5 0-1 0-1.5 4-7 4.5-7.25 0-2 2-4 2-4 2-4
D3UF-KA (4) CC 0-1.5 2.4 3.5-5.5 6.5-9 8.5-11 0-1 0-2 4-7 4.5-7.25 ..... ..... ..... .....
D3UF-LA (3) C 0-.5 0-2 5-7 7-9 8.25-10.5 0-1 1.5-4.5 4.5-7.25 4.5-7.25 0-3 4-7 5-7 5-7
D3UF-MA (3) C 0-.5 0-2 5-7 7-9 8.25-10.5 0-1.5 4.5-7.25 4.5-7.25 4.5-7.25 0-4.25 5-7 5-7 5-7
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.
(2) Basic number is 12127. Table gives prefix and suffix only.
(3) Dual Vacuum Diaphragm Distributor.
(4) Single Vacuum Diaphragm Distributor.
NOTE: FOR ENGINE RPM AND DEGREES, MULTIPLY SPECIFICATIONS BY 2.
1974 FORD MOTOR CO. DISTRIBUTOR ADVANCE SPECIFICATIONS

Distributor Part No. (2) Rot. (1) Automatic Advance (Distr. Degrees @ RPM) Vacuum Advance (Distr. Degrees) Operate Distr. @ 1000 RPM Vacuum Retard (Distr. Degrees) Operate Distr. @ 1000 RPM
500 750 1000 1500 2000 5 10 15 20 5 10 15 20
D3BF-BA (3) CC 0-1 2.5-4.5 6.5-8.5 8.5-11 9.5-12 0-1 0-2 5.5-8.5 8.5-11.5 0-3.5 5-7 5-7 5-7
D3BF-CA (3) C 0-1.5 3.5-5.5 6.5-8.5 8.5-10.5 10-12.5 0-1.25 4.25-7.25 4.25-7.25 4.25-7.25 0-2 2-4 2-4 2-4
D3TF-GA (4) C 0-1 .5-2.5 2.5-4.5 4-6 5.25-7.25 0-1.25 5-8 6.5-9.25 6.5-9.25 ..... ..... ..... .....
D3UF-BA (3) C 0-.5 0-1.5 2.5-4.5 6-8 7.5-10 0-1 1-4.5 4.5-7.25 4.5-7.25 0-3 4.5-7 5-7 5-7
D3UF-FA (3) CC 0-1.5 6-8 7.25-9.25 9.5-11.5 11.5-14 0-1.5 6.5-9.5 10.5-13.2 10.5-13.2 0-4 2-4 2-4 2-4
D3UF-JA (3) CC 0-1.5 2.5-4.5 5-7 6.5-9 8.25-10.5 0-1 0-1.5 4-7 4.5-7.25 0-2 2-4 2-4 2-4
D3UF-KA (4)(5) CC 0-1.5 2-4 3.5-5.5 6.5-9 8.5-11 0-1 0-2 4-7 4.5-7.25 ..... ..... ..... .....
D3UF-PA (3) C 0-1 0-2.5 5-7 7-9 8.25-10.5 2.5-5.5 2.5-5.5 2.5-5.5 2.5-5.5 0-3 4.5-7 5-7 5-7
D3UF-RA (3) C 0-.5 0-1.5 2.5-4.5 6-8 7.5-10 2.5-5.5 2.5-5.5 2.5-5.5 2.5-5.5 0-3 4.5-7 5-7 5-7
D4TE-CA (4)(5) CC 0-.5 0-.5 3-5 7-9 8.25-10.5 0-1.25 5-8 8.5-11.25 8.5-11.25 ..... ..... ..... .....
D4TE-HA (4)(5) CC 0-.5 0-2.5 6-8 7.5-9.5 8.5-11.25 0-1.25 5-8 8.5-11.25 8.5-11.25 ..... ..... ..... .....
D4TE-NA (4)(5) CC 0-.5 0-.5 .5-2.5 4.5-7 5.5-8.5 0-1.5 5-8 6.5-9.5 6.5-9.5 ..... ..... ..... .....
D4TE-PA (3)(5) CC 0-.5 0-1.5 1.5-3.5 6-8 9-11.5 0-1 0-2 5-8.5 8.5-11.5 0-4.5 5-7 5-7 5-7
D4TE-TA (4)(5) CC 0-1 4-6 6-8 10-12 13.5-16.5 3.5-6.5 4.5-7.25 4.5-7.25 4.5-7.25 ..... ..... ..... .....
D4TE-YA (4)(5) CC 0-.5 2.5-4.5 5.5-7.5 8.5-10.5 11-13.5 2.5-5.25 2.5-5.25 2.5-5.25 2.5-5.25 ..... ..... ..... .....
D4TZ-V (3)(5) CC 0-.5 2.5-4.5 4.5-6.5 6-8 7.5-10 0-.5 0-2 5.5-8.5 8.5-11.5 0-3.5 5-7 5-7 5-7
D4UE-CA (3)(5) CC 0-.5 2.5-4.5 4-6 6.5-8.5 8.5-11 0-1 0-3 6.5-9.5 8.5-11 0-4.5 5-7 5-7 5-7
D4UE-HA (3)(5) CC 0-.5 2.5-4.5 6.5-8.5 9-11 10-12.5 0-1.5 6.5-9.5 6.5-9.5 6.5-9.5 0-4 5-7 5-7 5-7
(1) C(Clockwise). CC(Counterclockwise) viewed from rotor end.
(2) Basic number is 12127. Table gives prefix and suffix only.
(3) Dual Vacuum Diaphragm Distributor.
(4) Single Vacuum Diaphragm Distributor.
(5) Breakerless Ignition.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.