Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2016 Fiat 500X Easy, 4WDFACTORY OEM SERVICE PROCEDURE
Module, Forward Facing Camera (FFCM)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| B1001-16 | POWER SUPPLY - CIRCUIT VOLTAGE BELOW THRESHOLD |
| B1001-17 | POWER SUPPLY - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| B1006-49 | HALF (HAPTIC LANE FEEDBACK) - INTERNAL ELECTRONIC FAILURE |
| B1007-54 | HALF (HAPTIC LANE FEEDBACK) - MISSING CALIBRATION |
| C0063-29 | YAW RATE SENSOR FROM BRAKE SYSTEM MODULE - SIGNAL - SIGNAL INVALID |
| C0546-00 | VIN (VEHICLE IDENTIFICATION NUMBER) IMPLAUSIBLE OR INCOMPATIBLE FROM BODY CONTROL MODULE - NO SUBTYPE INFORMATION |
| C1003-29 | VEHICLE SPEED INFORMATION FROM BRAKE SYSTEM MODULE - SIGNAL - SIGNAL INVALID |
| C14A5-97 | SENSOR BLINDED - COMPONENT OR SYSTEM OPERATION OBSTRUCTED OR BLOCKED |
| C14AA-64 | SENSOR ADJUSTMENT REQUIRED - SIGNAL PLAUSIBILITY FAILURE |
| C2210-4B | ECU OVERTEMPERATURE - OVER TEMPERATURE |
| U0001-88 | C3 CAN BUS (PRIVATE) - BUS OFF |
| U0101-87 | C2 CAN BUS - MISSING MESSAGE |
| U0101-88 | C2 CAN BUS - BUS OFF |
| U0422-29 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE - SIGNAL - SIGNAL INVALID |
| U1700-86 | BODY COMPUTER (BCM) - NODE FAULTY |
| U1700-87 | BODY COMPUTER (BCM) - NODE ABSENT |
| U1701-87 | U1701-87 ENGINE CONTROL MODULE (ECM) - MISSING MESSAGE |
| U1702-29 | ELECTRIC POWER STEERING (EPS) - SIGNAL - SIGNAL INVALID |
| U1702-64 | ELECTRIC POWER STEERING (EPS) - SIGNAL PLAUSIBILITY FAILURE |
| U1702-86 | ELECTRIC POWER STEERING (EPS) - SIGNAL INVALID |
| U1702-87 | ELECTRICAL POWER STEERING (EPS) - MISSING MESSAGE |
| U1706-86 | BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| U1706-87 | BRAKE SYSTEM MODULE (BSM) - MISSING MESSAGE |
| U1931-86 | HALF (HAPTIC LANE FEEDBACK) OPERATIONAL MODE STATUS - SIGNAL INVALID |
| U1932-86 | IGNITION WORKING CONDITION SIGNAL FROM BODY CONTROL MODULE - SIGNAL INVALID |
| U1950-83 | BCM_COMMAND (FROM BODY CONTROL MODULE) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1952-83 | BRAKE1 (FROM BRAKE SYSTEM MODULE) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1958-83 | BSM_YRS_DATA (FROM BRAKE SYSTEM MODULE) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U195E-83 | EPS_TORQUE_OVERLAY (FROM ELECTRIC POWER STEERING) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1966-83 | GE (FROM ELECTRIC POWER STEERING) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.