Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1996 Eagle Vision V6-201 3.3LFACTORY OEM SERVICE PROCEDURE
PCM - OBDII Readiness Code Retention
NUMBER: 18-005-01
GROUP: Vehicle Performance
DATE: Feb. 16, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 18-18-97,
DATED MAY 9, 1997, WHICH SHOULD BE REMOVED FROM YOUR
FILES. THIS IS A COMPLETE REVISION AND NO ASTERISKS HAVE
BEEN USED TO HIGHLIGHT REVISIONS.
SUBJECT:
OBDII Readiness Code Retention
OVERVIEW:
This bulletin involves reprogramming the Powertrain Control Module.
MODELS:
1995-1996 (JA) Cirrus/Stratus/Breeze
1996 (JX) Sebring Convertible
1996 (LH) Intrepid/Vision/Concorde/LHS
1996 (PL) Neon
NOTE:
THIS INFORMATION APPLIES TO FEDERAL EMISSION (SALES CODE NAA) AND CALIFORNIA EMISSION (SALES CODE NAE) MODELS BUILT PRIOR TO NOV. 21, 1995 (MDH1121XX) AND ALL 1995 JA MODELS EQUIPPED WITH A 2.0L ENGINE AND MANUAL TRANSAXLE. THE CALIFORNIA EMISSION MODELS ADDRESSED IN THIS BULLETIN WERE SOLD IN THE NORTHEAST STATES. CALIFORNIA MODELS SOLD IN CALIFORNIA WERE ADDRESSED WITH RECALL 678 DATED SEPT. 1996.
DISCUSSION:
The On Board Diagnostic (OBDII) system includes a monitor called readiness codes. The readiness codes indicate that all OBDII diagnostic tests have been performed and that diagnostic trouble codes (DTC's) can be read. It has been determined that the readiness codes may be cleared upon ignition key "OFF" cycles. Absence of readiness codes may cause owners to fail their emission inspection. To correct this condition, the Powertrain Control Module (PCM) must be reprogrammed.

PARTS REQUIRED:

EQUIPMENT REQUIRED:
NOTE:
THE MDS2 MUST BE OPERATING WITH CIS CD2075 OR HIGHER
1. Flash the PCM using the MDS2 (Mopar Diagnostic System) and DRBIII(R) (Scan Tool).
NOTE:
THE FOLLOWING STEPS ARE REQUIRED BY LAW.


2. Type the necessary information on the Authorized Software Update Label p/n 04669020 (Fig. 1). Attach the label to the PCM and cover it with the clear plastic overlay. Type the necessary information on the Authorized Modification Label p/n 04275086 (Fig. 2) and attach the label near the VECI label.
POLICY:
Reimbursable within the provisions of the warranty.

TIME ALLOWANCE:

FAILURE CODE:
GROUP: Vehicle Performance
DATE: Feb. 16, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 18-18-97,
DATED MAY 9, 1997, WHICH SHOULD BE REMOVED FROM YOUR
FILES. THIS IS A COMPLETE REVISION AND NO ASTERISKS HAVE
BEEN USED TO HIGHLIGHT REVISIONS.
SUBJECT:
OBDII Readiness Code Retention
OVERVIEW:
This bulletin involves reprogramming the Powertrain Control Module.
MODELS:
1995-1996 (JA) Cirrus/Stratus/Breeze
1996 (JX) Sebring Convertible
1996 (LH) Intrepid/Vision/Concorde/LHS
1996 (PL) Neon
NOTE:
THIS INFORMATION APPLIES TO FEDERAL EMISSION (SALES CODE NAA) AND CALIFORNIA EMISSION (SALES CODE NAE) MODELS BUILT PRIOR TO NOV. 21, 1995 (MDH1121XX) AND ALL 1995 JA MODELS EQUIPPED WITH A 2.0L ENGINE AND MANUAL TRANSAXLE. THE CALIFORNIA EMISSION MODELS ADDRESSED IN THIS BULLETIN WERE SOLD IN THE NORTHEAST STATES. CALIFORNIA MODELS SOLD IN CALIFORNIA WERE ADDRESSED WITH RECALL 678 DATED SEPT. 1996.
DISCUSSION:
The On Board Diagnostic (OBDII) system includes a monitor called readiness codes. The readiness codes indicate that all OBDII diagnostic tests have been performed and that diagnostic trouble codes (DTC's) can be read. It has been determined that the readiness codes may be cleared upon ignition key "OFF" cycles. Absence of readiness codes may cause owners to fail their emission inspection. To correct this condition, the Powertrain Control Module (PCM) must be reprogrammed.
PARTS REQUIRED:
EQUIPMENT REQUIRED:
NOTE:
THE MDS2 MUST BE OPERATING WITH CIS CD2075 OR HIGHER
1. Flash the PCM using the MDS2 (Mopar Diagnostic System) and DRBIII(R) (Scan Tool).
NOTE:
THE FOLLOWING STEPS ARE REQUIRED BY LAW.
2. Type the necessary information on the Authorized Software Update Label p/n 04669020 (Fig. 1). Attach the label to the PCM and cover it with the clear plastic overlay. Type the necessary information on the Authorized Modification Label p/n 04275086 (Fig. 2) and attach the label near the VECI label.
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
FAILURE CODE:
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
