Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2024 Dodge and Ram ProMaster 1500 SLT+FACTORY OEM SERVICE PROCEDURE
Module, Forward Facing Camera (FFCM)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| B1006-49 | HALF (HAPTIC LANE FEEDBACK) - INTERNAL ELECTRONIC FAILURE |
| B1007-54 | HALF (HAPTIC LANE FEEDBACK) - MISSING CALIBRATION |
| B1EAB-00 | STEERING WHEEL CRUISE CONTROL SWITCH |
| B1EAB-86 | STEERING WHEEL CRUISE CONTROL SWITCH - SIGNAL INVALID |
| B210A-00 | SYSTEM VOLTAGE LOW - NO SUBTYPE INFORMATION |
| B210B-00 | SYSTEM VOLTAGE HIGH - NO SUBTYPE INFORMATION |
| B2206-00 | CURRENT VIN MISMATCH - NO SUBTYPE INFORMATION |
| C0031-64 | LEFT FRONT WHEEL SPEED SENSOR - SIGNAL PLAUSIBILITY FAILURE |
| C0034-64 | RIGHT FRONT WHEEL SPEED SENSOR - SIGNAL PLAUSIBILITY FAILURE |
| C0037-64 | LEFT REAR WHEEL SPEED SENSOR - SIGNAL PLAUSIBILITY FAILURE |
| C003A-64 | RIGHT REAR WHEEL SPEED SENSOR - SIGNAL PLAUSIBILITY FAILURE |
| C003F-00 | WHEEL SPEED SENSORS ROTATION DIRECTION CORRELATION - NO SUBTYPE INFORMATION |
| C0061-64 | LATERAL ACCELERATION SENSOR - SIGNAL PLAUSIBILITY FAILURE |
| C0062-64 | LONGITUDINAL ACCELERATION SENSOR - SIGNAL PLAUSIBILITY FAILURE |
| C0063-29 | YAW RATE SENSOR - SIGNAL SIGNAL INVALID |
| C0063-64 | YAW RATE SENSOR - SIGNAL PLAUSIBILITY FAILURE |
| C10F6-53 | BRAKE ROLLS MODE ACTIVE - DEACTIVATED |
| C1226-64 | BRAKE PEDAL MASTER CYLINDER PRESSURE - SIGNAL PLAUSIBILITY FAILURE |
| C1260-00 | ABS/ESC DYNAMIC CONTROLS DISABLED - NO SUBTYPE INFORMATION |
| C1407-86 | ACKNOWLEDGE SIGNAL FAIL FROM BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| C1409-97 | RADAR - COMPONENT OR SYSTEM OPERATION OBSTRUCTED OR BLOCKED |
| C140C-86 | HALF INTERVENTION REQUEST TIME OUT OF RANGE - SIGNAL INVALID |
| C1413-86 | EXTERNAL LIGHT SIGNAL FAULT - SIGNAL INVALID |
| C1415-53 | FORWARD COLLISION WARNING (FCW) UNAVAILABLE - DEACTIVATED |
| C1422-00 | INTERNAL HW PLAUSIBILITY CHECK - NO SUBTYPE INFORMATION |
| C1432-86 | TURN INDICATOR FAILURE FROM BODY CONTROL MODULE (BCM) - SIGNAL INVALID |
| C1433-86 | EXTERNAL BRAKE SIGNAL FAILURE FROM BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| C1434-86 | BRAKE JERK REQUEST NOT PLAUSIBLE - SIGNAL INVALID |
| C1436-86 | ELECTRIC PARKING BRAKE SYSTEM FAIL - SIGNAL INVALID |
| C1451-86 | ACC (ADAPTIVE CRUISE CONTROL) SAFE - SIGNAL INVALID |
| C1453-86 | ACC (ADAPTIVE CRUISE CONTROL) INTERVENTION SIGNALS NOT PLAUSIBLE - SIGNAL INVALID |
| C14A5-92 | SENSOR BLINDED - PERFORMANCE OR INCORRECT OPERATION |
| C14A5-97 | SENSOR BLINDED - COMPONENT OR SYSTEM OPERATION OBSTRUCTED OR BLOCKED |
| C14AA-64 | SENSOR ADJUSTMENT REQUIRED - SIGNAL PLAUSIBILITY FAILURE |
| C1600-94 | SUPPLIER MODE ACTIVE - UNEXPECTED OPERATION |
| C2210-4B | ECU OVERTEMPERATURE - OVER TEMPERATURE |
| P0780-68 | GEAR SHIFT MALFUNCTION - EVENT INFORMATION |
| P1C81-00 | SHIFT LEVER POSITION INDETERMINATE - NO SUBTYPE INFORMATION |
| P1DCB-64 | REVERSE GEAR SWITCH - SIGNAL PLAUSIBILITY FAILURE |
| U0055-00 | CAN C2 BUS-NO SUBTYPE INFORMATION |
| U0056-00 | CAN C2 BUS OFF PERFORMANCE-NO SUBTYPE INFORMATION |
| U0100-00 | LOST COMMUNICATION WITH ECM - NO SUBTYPE INFORMATION |
| U0121-00 | LOSS OF COMMUNICATION WITH BRAKE SYSTEM MODULE (BSM) - NO SUBTYPE INFORMATION |
| U0131-00 | LOSS OF COMMUNICATION WITH ELECTRIC POWER STEERING (EPS) - NO SUBTYPE INFORMATION |
| U0140-00 | LOST COMMUNICATION WITH BODY CONTROL MODULE (BCM) - NO SUBTYPE INFORMATION |
| U0151-87 | LOST COMMUNICATION WITH OCCUPANT RESTRAINT CONTROLLER (ORC) - MISSING MESSAGE |
| U0155-00 | LOSS OF COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) - NO SUBTYPE INFORMATION |
| U0159-00 | LOST COMMUNICATION WITH PAM - NO SUBTYPE INFORMATION |
| U0401-00 | IMPLAUSIBLE DATA RECEIVED FROM BSM (BRAKE SYSTEM MODULE) - NO SUBTYPE INFORMATION |
| U0418-64 | INVALID DATA RECEIVED FROM BRAKE SYSTEM MODULE (BSM) - SIGNAL PLAUSIBILITY FAILURE |
| U0420-64 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING (EPS) - SIGNAL PLAUSIBILITY FAILURE |
| U0422-64 | INVALID DATA RECEIVED FROM BODY CONTROL MODULE - SIGNAL PLAUSIBILITY FAILURE |
| U1216-00 | LOST COMMUNICATION WITH DRIVER ASSISTANCE SYSTEM MODULE - NO SUBTYPE INFORMATION |
| U1216-87 | LOST COMMUNICATION WITH DRIVER ASSISTANCE SYSTEM MODULE - MISSING MESSAGE |
| U1412-00 | IMPLAUSIBLE VEHICLE SPEED SIGNAL RECEIVED - NO SUBTYPE INFORMATION |
| U1415-00 | IMPLAUSIBLE/MISSING VEHICLE CONFIGURATION DATA - NO SUBTYPE INFORMATION |
| U1425-00 | IMPLAUSIBLE PEDAL POSITION SIGNAL RECEIVED - NO SUBTYPE INFORMATION |
| U1464-64 | IMPLAUSIBLE DATA RECEIVED FROM EPS STEERING TORQUE - SIGNAL PLAUSIBILITY FAILURE |
| U147A-00 | IMPLAUSIBLE BRAKE PEDAL POSITION SIGNAL RECEIVED - NO SUBTYPE INFORMATION |
| U148A-64 | IMPLAUSIBLE DATA RECEIVED FROM DRIVER ASSISTANCE SYSTEM MODULE - SIGNAL PLAUSIBILITY FAILURE |
| U148A-83 | IMPLAUSIBLE DATA RECEIVED FROM DRIVER ASSISTANCE SYSTEM MODULE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1518-00 | IMPLAUSIBLE AMBIENT AIR TEMPERATURE SIGNAL RECEIVED - NO SUBTYPE INFORMATION |
| U1600-54 | ECU APPLICATION SOFTWARE MISMATCH - MISSING CALIBRATION |
| U1930-86 | HALF (HAPTIC LANE FEEDBACK) OPERATIONAL MODE STATUS - SIGNAL INVALID |
| U1950-83 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE (CAN MESSAGE BCM_COMMAND INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1952-61 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BRAKE1 INTEGRITY ERROR) - SIGNAL CALCULATION FAILURE |
| U1952-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BRAKE1 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1958-61 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BSM_YRS_DATA INTEGRITY ERROR) - SIGNAL CALCULATION FAILURE |
| U1958-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BSM_YRS_DATA INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U195E-83 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING (CAN MESSAGE EPS_TORQUE_OVERALAY INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1960-61 | IMPLAUSIBLE DATA RECEIVED FROM ECM (CAN MESSAGE ENGINE1 INTEGRITY ERROR) - SIGNAL CALCULATION FAILURE |
| U1960-83 | IMPLAUSIBLE DATA RECEIVED FROM ECM (CAN MESSAGE ENGINE1 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1966-61 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING (CAN MESSAGE GE INTEGRITY ERROR) - SIGNAL CALCULATION FAILURE |
| U1966-83 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING (CAN MESSAGE GE INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1978-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE STATUS_EPB INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1982-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE WHEEL_INFO INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1984-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE WHEEL_SPEED INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1986-83 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE (CAN MESSAGE SCCM_CRS_CTRL INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U198A-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BRAKE7 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U19A4-64 | HALF (HAPTICAL LANE FEEDBACK) FAIL SAFE VIOLATION - SIGNAL PLAUSIBILITY FAILURE |
| U19BD-83 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE (CAN MESSAGE SWSM_1 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U19BE-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BRAKE18 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U19BF-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BRAKE19 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U19C0-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BRAKE17 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.