Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Dodge and Ram ProMaster 2500FACTORY OEM SERVICE PROCEDURE
Module, Powertrain Control (Pcm), 62TE
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| P0124 | TPS/APP INTERMITTENT |
| P0218 | HIGH TEMPERATURE OPERATION ACTIVATED |
| P0562 | BATTERY/SYSTEM VOLTAGE LOW |
| P0602 | CONTROL MODULE PROGRAMMING ERROR/NOT PROGRAMMED |
| P0613 | INTERNAL TRANSMISSION PROCESSOR |
| P0706 | TRANSMISSION RANGE SENSOR RATIONALITY |
| P0711 | TRANSMISSION TEMPERATURE SENSOR 1 PERFORMANCE |
| P0712 | TRANSMISSION TEMPERATURE SENSOR 1 LOW |
| P0713 | TRANSMISSION TEMPERATURE SENSOR 1 HIGH |
| P0714 | TRANSMISSION TEMPERATURE SENSOR 1 INTERMITTENT |
| P0716 | INPUT SHAFT SPEED SENSOR 1 PERFORMANCE |
| P0721 | OUTPUT SPEED SENSOR CIRCUIT PERFORMANCE |
| P0726 | ENGINE SPEED INPUT CIRCUIT PERFORMANCE |
| P0729 | GEAR RATIO ERROR IN 6TH |
| P0731 | GEAR RATIO ERROR IN 1ST |
| P0732 | GEAR RATIO ERROR IN 2ND |
| P0733 | GEAR RATIO ERROR IN 3RD |
| P0734 | GEAR RATIO ERROR IN 4TH |
| P0735 | GEAR RATIO ERROR IN 5TH |
| P0736 | GEAR RATIO ERROR IN REVERSE |
| P0740 | TCC OUT OF RANGE |
| P0750 | L/R SOLENOID CIRCUIT |
| P0755-2/4 | SOLENOID CIRCUIT |
| P075A-LC | SOLENOID CIRCUIT |
| P0760-OD | SOLENOID CONTROL CIRCUIT |
| P0765-UD | SOLENOID CIRCUIT |
| P076A-DC | SOLENOID CIRCUIT |
| P0791 | INTERMEDIATE SHAFT SPEED SENSOR CIRCUIT |
| P0792 | COMPOUNDER SPEED RATIO ERROR |
| P083A-LC | HYDRAULIC PRESSURE TEST |
| P083B-LC | PRESSURE SWITCH RATIONALITY |
| P0841-L/R | PRESSURE SWITCH RATIONALITY |
| P0845-2-4 OR 2C | HYDRAULIC PRESSURE TEST |
| P0846-2-4 OR 2C | PRESSURE SWITCH RATIONALITY |
| P084A-DC | HYDRAULIC PRESSURE TEST |
| P084B-DC | PRESSURE SWITCH RATIONALITY |
| P0868 | LINE PRESSURE LOW |
| P0869 | LINE PRESSURE HIGH |
| P0870-OD | HYDRAULIC PRESSURE TEST |
| P0871-OD | PRESSURE SWITCH RATIONALITY |
| P0882-TCM | POWER INPUT LOW |
| P0883 | TCM POWER INPUT HIGH |
| P0884 | POWER UP AT SPEED |
| P0890 | SWITCHED BATTERY |
| P0933 | HYDRAULIC PRESSURE SENSOR RANGE/PERFORMANCE |
| P0934 | LINE PRESSURE SENSOR CIRCUIT LOW |
| P0935 | HYDRAULIC PRESSURE SENSOR CIRCUIT HIGH |
| P0944 | LOSS OF HYDRAULIC PUMP PRIME |
| P0957 | AUTOSTICK CIRCUIT LOW |
| P0992 | 2/4/OD HYDRAULIC PRESSURE TEST |
| P1713 | RESTRICTED MANUAL VALVE IN T2 RANGE |
| P1741 | GEAR RATIO ERROR IN 4 PRIME |
| P1745 | TRANSMISSION LINE PRESSURE TOO HIGH FOR TOO LONG |
| P1771 | INADEQUATE ELEMENT VOLUME 24 (FWD) OR 2C (RWD) |
| P1775 | SOLENOID SWITCH VALVE LATCHED IN TCC POSITION |
| P1776 | SOLENOID SWITCH VALVE LATCHED IN LR POSITION |
| P1790 | FAULT IMMEDIATELY AFTER SHIFT |
| P1794 | SPEED SENSOR GROUND ERROR |
| P1797 | MANUAL SHIFT OVERHEAT |
| P2700 | INADEQUATE ELEMENT VOLUME LR |
| P2702 | INADEQUATE ELEMENT VOLUME OD |
| P2703 | INADEQUATE ELEMENT VOLUME UD |
| P273A | INADEQUATE ELEMENT VOLUME LC |
| P273B | INADEQUATE ELEMENT VOLUME DC |
| P2763 | TORQUE CONVERTER CLUTCH PRESSURE CONTROL CIRCUIT HIGH |
| P2764 | TORQUE CONVERTER CLUTCH PRESSURE CONTROL CIRCUIT LOW |
| U0002 | CAN C BUS OFF PERFORMANCE |
| U0100 | LOST COMMUNICATION WITH ECM/PCM |
| U0121 | LOST COMMUNICATION WITH ABS |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.