Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
1989 Dodge and Ram Colt Vista 4WD
Labor Times
1989 Dodge and Ram Colt Vista 4WDSECTION Labor Times
- Accessories and Equipment
- Exterior Lights
- Gauges and Instrument Panels
- Headlights
- Ignition Switches and Steering Locks
- Warning Systems
- Window Motors and Regulators
- Wiper & Washer Systems
- Brakes
- Drivelines and Axles
- Axle Shafts - Front
- Axle Shafts - Rear
- Differentials and Drive Axles - Front
- Differentials and Drive Axles - Rear
- Driveshafts and Universal Joints
- Electrical
- Engine Mechanical
- Auxiliary Emission Control Systems
- Cooling Fan
- Cooling System (Mechanical)
- Exhaust
- Fuel Systems
- Lubrication Systems
- Mechanical
- Balance Shaft
- Balance Shaft Carrier
- Camshaft
- Camshaft Bearing Set
- Camshaft Or Oil Galley Plug
- Camshaft Seal
- Connecting Rod Bearings
- Crankshaft
- Crankshaft Main Oil Seal
- Crankshaft Oil Seal
- Crankshaft Pulley
- Cylinder Head Gasket
- Engine Assembly
- Engine Assembly (Complete)
- Engine Or Transmission Mount
- Engine Torque Mount
- Intermediate Shaft
- Intermediate Shaft Seal
- Intermediate Shaft Sprocket
- Long Block
- Main Bearings
- Piston Ring Set
- Rocker Arm Assembly
- Short Block
- Timing Belt
- Timing Belt TENSIONER
- Valve
- Valve Cover Gasket
- Valve Spring Or Seal
- Starters
- Engine Performance
- Fuel Delivery System
- Air Charge Temperature Sensor
- Air Cleaner Element
- Air Flow Sensor
- Ambient Temperature Sensor
- Coolant Temperature Sensor
- Crankshaft Position Sensor
- Electronic Control Module
- Engine Idle Speed
- Fuel Injection System
- Fuel Injector
- Intake Manifold
- Intake Manifold Gasket
- Manifold Absolute Pressure Sensor
- Throttle Position Sensor
- Vehicle Speed/Distance Sensor
- Ignition Systems
- Crankshaft Position Sensor
- Distributor Assembly
- Distributor Cap
- Distributor Vacuum Control
- Electronic Ignition Breaker Assembly
- Electronic Ignition Module
- Electronic Ignition Pick-Up
- Electronic Ignition RELUCTOR
- Engine Compression
- Engine Cylinder Leakage
- Engine Performance
- Ignition Coil
- Ignition Timing
- Spark Plug Wire Set
- Spark Plugs
- Top Dead Center (TDC) Sensor
- Fuel Delivery System
- Heating, Ventilation & A/C (HVAC)
- A/C Compressor
- Heater
- Manual HVAC System
- Steering
- Suspension
- Front Suspension
- Rear Suspension
- Wheel and Tire Systems
- Transmission
- Automatic Trans
- Accumulator Piston
- Differential Assembly
- Differential Cover Gasket
- Extension Housing Seal
- KICKDOWN Band
- KICKDOWN Servo
- KICKDOWN Switch
- Main Control Valve Body
- Neutral Safety Switch
- Parking Lock Rod
- Parking Sprag
- Reverse Servo
- Speedometer Driven Gear
- Throttle Linkage
- Throttle Valve Lever Shaft Seal
- Transaxle Assembly
- Transaxle Oil Filter
- Transaxle Oil Pan Gasket
- Transmission
- Transmission Assembly
- Valve Body Lever Shaft Seal
- Clutch Manual and Hydraulic
- Clutch Control Cable
- Clutch Hydraulic System
- Clutch Master Cylinder
- Clutch Master Cylinder Reservoir
- Clutch Pedal
- Clutch Pilot Bearing Or Bushing
- Clutch Pressure Plate
- Clutch Release Bearing
- Clutch Slave Cylinder
- Flywheel (Removed)
- Flywheel (Std Trans)
- Flywheel Ring Gear
- Gearshift Control Assembly
- Gearshift Rod
- Hydraulic Clutch Hose
- Shift Control Cable
- Manual Trans
- Transfer Case
- Automatic Trans
- Body and Frame
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.