Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2001 Daewoo Leganza CDXFACTORY OEM SERVICE PROCEDURE
Torque Specifications
TORQUE SPECIFICATIONS
| Application | N.m (Ft. Lbs.) |
|---|---|
| Accessory Mounting Bracket Bolts | 35 (26) |
| Engine Coolant Temperature Sensor | 20 (15) |
| Evaporative Emission Canister Flange Bolt | 20 (15) |
| Exhaust Gas Recirculation Valve Retaining Bolts | 30 (22) |
| Fuel Rail Retaining Bolts | 25 (18) |
| Heated Oxygen Sensor | 42 (31) |
| Knock Sensor Bolt | 20 (15) |
| Oxygen Sensor | 42 (31) |
| Rear A/C Compressor Mounting Bracket Bolts | 35 (26) |
| N.m (INCH Lbs.) | |
| Camshaft Position Bolts | 7 (62) |
| Crankshaft Position Sensor Retaining Bolt | 6.5 (58) |
| Electronic Ignition System Ignition Coil Retaining Bolts | 10 (89) |
| Evaporative Emission Canister Protective Cover | 8 (71) |
| Evaporative Emission Canister Purge Solenoid Bracket Bolts | 5 (44) |
| Fuel Cutoff Switch Bolts | 3 (27) |
| Fuel Pressure Regulator Retaining Clamp | 12 (106) |
| Fuel Tank Strap Retaining Nuts | 13 (115) |
| Idle Air Control Valve Retaining Bolts | 3 (27) |
| Manifold Absolute Pressure Sensor Retaining Bolt | 10 (89) |
| Throttle Body Retaining Nuts | 10 (89) |
| Throttle Cable Bracket Bolts | 10 (89) |
| Throttle Position Sensor Retaining Bolts | 2 (18) |
Torque Specifications
| Application | N.m | Lb-Ft | Lb-In |
|---|---|---|---|
| Accessory Mounting Bracket Bolts | 35 | 26 | - |
| Camshaft Position Bolts | 7 | - | 62 |
| Crankshaft Position Sensor Retaining Bolt | 6.5 | - | 58 |
| Electronic Ignition System Ignition Coil Retaining Bolts | 10 | - | 89 |
| Engine Coolant Temperature Sensor | 20 | 15 | - |
| Evaporative Emission Canister Flange Bolt | 20 | 15 | - |
| Evaporative Emission Canister Protective Cover | 8 | - | 71 |
| Evaporative Emission Canister Purge Solenoid Bracket Bolts | 5 | - | 44 |
| Exhaust Gas Recirculation Valve Retaining Bolts | 30 | 22 | - |
| Fuel Cutoff Switch Bolts | 3 | - | 27 |
| Fuel Pressure Regulator Retaining Clamp | 12 | - | 106 |
| Fuel Rail Retaining Bolts | 25 | 18 | - |
| Fuel Tank Strap Retaining Nuts | 13 | - | 115 |
| Heated Oxygen Sensor | 42 | 31 | - |
| Idle Air Control Valve Retaining Bolts | 3 | - | 27 |
| Knock Sensor Bolt | 20 | 15 | - |
| Manifold Absolute Pressure Sensor Retaining Bolt | 10 | - | 89 |
| Oxygen Sensor | 42 | 31 | - |
| Rear A/C Compressor Mounting Bracket Bolts | 35 | 26 | - |
| Throttle Body Retaining Nuts | 10 | - | 89 |
| Throttle Cable Bracket Bolts | 10 | - | 89 |
| Throttle Position Sensor Retaining Bolts | 2 | - | 18 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.