2011 Chrysler 300 Base, GasFACTORY OEM SERVICE PROCEDURE

Diagnostic Test

  1. VERIFY THE DTC IS ACTIVE 
    1. Ignition on, engine not running.
    2. With the scan tool, read DTCs.

      Is the DTC active at this time?

      Yes 

      • Go To  2.

      No 

      • Go To  10.
  2. TRANSFER CASE MOTOR (AWD) OPERATION 
    Fig 1: Checking Transfer Case Motor (AWD) Operation
    GC0096561Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Disconnect the Transfer Case Motor (AWD) C1 harness connector.
    3. Ignition on, engine not running.
    4. Using a 12-volt test light, jump across from the (T315) Shift Motor Control A circuit and the (T316) Shift Control Motor B circuit at the Transfer Case Motor C1 harness connector.
    5. With the scan tool, actuate the Transfer Case Motor (AWD).

      Does the test light illuminate brightly and flash on and off?

      Yes 

      • Go To  9.

      No 

      • Go To  3.
  3. (T316) SHIFT CONTROL MOTOR B CIRCUIT SHORTED TO GROUND 
    Fig 2: Checking Shift Control Motor B Circuit For Short Ground
    GC0096562Courtesy of CHRYSLER LLC
    1. Turn the ignition off to the lock position.
    2. Disconnect the DTCM harness connector.
    3. Measure the resistance between ground and the (T316) Shift Control Motor B circuit at the Transfer Case Motor (AWD) C1 harness connector.

      Is the resistance below 100 Ohms?

      Yes 

      • Repair the short to ground in the (T316) Shift Control Motor B circuit.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.

      No 

      • Go To  4.
  4. (T316) SHIFT CONTROL MOTOR B CIRCUIT OPEN 
    Fig 3: Checking Shift Control Motor B Circuit For Open
    GC0096563Courtesy of CHRYSLER LLC
    1. Measure the resistance of the (T316) Shift Control Motor B circuit between the Transfer Case Motor (AWD) C1 harness connector and the DTCM harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  5.

      No 

      • Repair the open in the (T316) Shift Control Motor B circuit.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.
  5. (T315) SHIFT MOTOR CONTROL A CIRCUIT SHORTED TO GROUND 
    Fig 4: Checking Shift Motor Control A Circuit For Short To Ground
    GC0096564Courtesy of CHRYSLER LLC
    1. Measure the resistance between ground and the (T315) Shift Motor Control A circuit at the Transfer Case Motor (AWD) C1 harness connector.

      Is the resistance below 100 Ohms?

      Yes 

      • Repair the short to ground in the (T315) Shift Motor Control A circuit.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.

      No 

      • Go To  6.
  6. (T315) SHIFT MOTOR CONTROL A CIRCUIT OPEN 
    Fig 5: Checking Shift Motor Control A Circuit For Open
    GC0096565Courtesy of CHRYSLER LLC
    1. Measure the resistance of the (T315) Shift Motor Control A circuit between the Transfer Case Motor (AWD) C1 harness connector and the DTCM harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  7.

      No 

      • Repair the open in the (T315) Shift Motor Control A circuit.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.
  7. TRANSFER CASE MOTOR (T316) SHIFT CONTROL MOTOR B CIRCUIT SHORTED INTERNALLY 
    Fig 6: Checking Transfer Case Motor Shift Control Motor B Circuit For Short Internally
    GC0096566Courtesy of CHRYSLER LLC
    1. Turn the ignition off to the lock position.
    2. Connect the Transfer Case Motor (AWD) C1 harness connector.
    3. Measure the resistance between ground and the (T316) Shift Control Motor B circuit at the DTCM harness connector.

      Is the resistance below 100 Ohms?

      Yes 

      • Repair the short to ground in the (T316) Shift Control Motor B circuit.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.

      No 

      • Go To  8.
  8. DRIVE TRAIN CONTROL MODULE (DTCM) 
    NOTE:

    Before continuing, check the DTCM harness connector terminals for corrosion, damage or terminal push out. Repair as necessary.

    1. Using the schematics as a guide, inspect the wiring harness and connectors. Pay particular attention to all Power and Ground circuits.

      Were there any problems found?

      Yes 

      • Repair as necessary.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.

      No 

  9. TRANSFER CASE MOTOR (AWD) 
    NOTE:

    Before continuing, check the Transfer Case Motor jumper harness connector terminals for corrosion, damage, or terminals push out, repair/replace as necessary.

    1. Using the schematics as a guide, inspect the wiring harness and connectors. Pay particular attention to all Power and Ground circuits.

      Were there any problems found?

      Yes 

      • Repair as necessary.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.

      No 

  10. INTERMITTENT WIRING HARNESS AND CONNECTORS 
    1. The conditions necessary to set this DTC are not present at this time.
    2. Using the schematics as a guide, inspect the wiring harness and connectors specific to this circuit.
    3. Wiggle test the wiring harness and connectors while checking for shorted and open circuits.
    4. Using the scan tool, monitor the data related to this circuit while performing the wiggle test. Look for the data to change or for the DTC to reset.

      Were there any problems found?

      Yes 

      • Repair as necessary.
      • Refer to Standard Procedure  and perform the DTCM VERIFICATION TEST.

      No 

      • Test Complete.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.