SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER2003INTREPID SXTREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROLS - SELF-DIAGNOSTICSVERIFICATION TESTSPOWERTRAIN VERIFICATION TEST VER-4
2003 Chrysler Intrepid SXT

Powertrain Verification Test VER-4

2003 Chrysler Intrepid SXTSECTION Powertrain Verification Test VER-4
NOTE: If replacing the PCM, the correct vehicle mileage and Vehicle Identification Number (VIN) must be programmed into PCM to prevent DTCs from being stored in Controller Anti-Lock Brake (CAB) module, and Air Bag Control Module (ACM). If replacing PCM and vehicle is equipped with a Smart Key Immobilizer Module (SKIM), secret key data must also be updated to enable engine starting. See PROGRAMMING . After completing this verification test, the 42LE Transmission verification test must be performed.
  1. Inspect vehicle to ensure all engine and speed control system components are connected. Reassemble and reconnect components as necessary. Using DRBIII® scan tool, record and erase Diagnostic Trouble Codes (DTC) from PCM.
  2. Road test vehicle at a speed greater than 35 MPH. Turn speed control switch on. Press and release SET switch and verify speed control engages. If speed control engages, go to next step. If speed control does not engage, go to step  11.
  3. With speed control engaged, depress and hold ACCEL switch. If vehicle speed increases, release switch and go to next step. If vehicle speed does not increase, go to step  11.
  4. Press and hold COAST switch. If vehicle speed decreases, release switch and go to next step. If vehicle speed does not decrease, go to step  11.
  5. Depress and release CANCEL switch. If speed control disengages, go to next step. If speed control does not disengage, go to step  11.
  6. Bring vehicle speed back to 35 MPH and depress RESUME switch. If vehicle resumes previously set speed, go to next step. If vehicle does not resume previously set speed, go to step  11.
  7. Using caution, press and release brake pedal to activate brakelight switch. If speed control disengages, go to next step. If speed control does not disengage, go to step  11.
  8. Increase vehicle speed to more than 35 MPH. Press and release SET switch. If vehicle maintains new set speed, go to next step. If vehicle does not set or maintain a new set speed, go to step  11.
  9. Depress and release ON/OFF switch to OFF position. If speed control disengages, go to next step. If speed control did not disengage, go to step  11.
  10. Using DRBIII® scan tool, check for DTCs. If no DTCs are present and vehicle is operating as designed, repair is complete. Perform transmission verification test. See 42LE TRANSMISSION VERIFICATION TEST VER-1 . If DTCs exist, or system is not operating as designed, go to next step.
  11. If speed control does not operate properly or DTCs exist, refer to appropriate diagnostic or repair procedures. See DIAGNOSTIC TROUBLE CODE DEFINITIONS . Check for any related technical service bulletins that may apply.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.