Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER2003INTREPID SEREPAIR AND DIAGNOSISTRANSMISSIONAUTOMATIC TRANSAUTOMATIC TRANSMISSION DIAGNOSTIC PROCEDURES
2003 Chrysler Intrepid SE
Automatic Transmission Diagnostic Procedures
2003 Chrysler Intrepid SESECTION Automatic Transmission Diagnostic Procedures
- Introduction
- Identification Of System
- System Description And Functional Operation
- Disclaimers, Safety, And Warnings
- Required Tools And Equipment
- Glossary Of Terms
- Diagnostic Information And Procedures
- Communication - Symptoms
- Transmission - NGC - Symptoms
- Symptom: *BACKUP LAMPS COME ON WHILE SHIFTER IS NOT IN REVERSE POSITION
- Symptom: *BACKUP LAMPS INOPERATIVE
- Symptom: *CHECKING PARK/NEUTRAL SWITCH OPERATION
- Symptom: *NO MANUAL AUTOSTICK OPERATION
- Symptom: *PRNDL FAULT CLEARING PROCEDURE
- Symptom: *TRANSMISSION NOISY WITH NO DTC'S PRESENT
- Symptom: *TRANSMISSION SHIFTS EARLY WITH NO DTC'S
- Symptom: *TRANSMISSION SIMULATOR 8333 WILL NOT POWER UP
- Transmission - NGC - Diagnostic Tests
- P0122-Throttle Position Sensor/Apps Low
- P0123-Throttle Position Sensor/Apps High
- P0124-Throttle Position Sensor/Apps Intermittent
- P0218-High Temperature Operation Activated
- P0562-Low Battery Voltage
- P0604-Internal TCM, P0605-Internal TCM, P0613-Internal TCM
- P0706-Check Shifter Signal
- P0711-Transmission Temperature Sensor Performance
- P0712-Transmission Temperature Sensor Low
- P0713-Transmission Temperature Sensor High
- P0714-Transmission Temperature Sensor Intermittent
- P0715-Input Speed Sensor Error
- P0720-Output Speed Sensor Error
- P0725-Engine Speed Sensor Circuit
- P0731-Gear Ratio Error In 1ST
- P0732-Gear Ratio Error In 2ND
- P0733-Gear Ratio Error In 3RD
- P0734-Gear Ratio Error In 4TH
- P0736-Gear Ratio Error In Reverse
- P0740-Torque Converter Clutch Control Circuit
- P0750-LR Solenoid Circuit
- P0755-2/4 Solenoid Circuit
- P0760-Od Solenoid Circuit
- P0765-UD Solenoid Circuit
- P0841-LR Pressure Switch Sense Circuit
- P0845-2/4 Hydraulic Pressure Test Failure
- P0846-2/4 Pressure Switch Sense Circuit
- P0870-Od Hydraulic Pressure Test Failure
- P0871-Od Pressure Switch Sense Circuit
- P0884-Power Up At Speed
- P0888-Relay Output Always Off
- P0890-Switched Battery
- P0891-Transmission Relay Always On
- P0897-Worn Out/Burnt Transaxle Fluid
- P0944-Loss Of Prime
- P0952-AUTOSTICK Input Circuit Low
- P0992-2-4/Od Hydraulic Pressure Test Failure
- P1652-Serial Communication Link Malfunction
- P1684-Battery Was Disconnected
- P1687-No Communication With The Mic
- P1694-Bus Communication With Engine Module
- P1775-Solenoid Switch Valve Latched In TCC Position
- P1776-Solenoid Switch Valve Latched In LR Position
- P1790-Fault Immediately After Shift
- P1793-TRD Link Communication Error
- P1794-Speed Sensor Ground Error
- P1797-Manual Shift Overheat
- Verification Tests
- Component Locations
- Connector PINOUTS
- Schematic Diagrams
- Charts And Graphs
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.