2002 Chrysler Voyager ECFACTORY OEM SERVICE PROCEDURE

Body Verification Test

  1. Disconnect all jumper wires and reconnect all previously disconnected components and connectors.
  2. With the DRBIII® record and erase all DTCs from all modules. Cycle the ignition on then off.
  3. If the Sentry Key Immobilizer Module (SKIM), the Powertrain Control Module (PCM), or the Engine Control Module (ECM) was replaced, proceed to step  12. If the SKIM, PCM, or ECM was not replaced, continue to the next number.
  4. If the Body Control Module (BCM) was replaced, turn the ignition on for 15 seconds (to allow the new BCM to learn VIN) or engine may not start (if VTSS equipped). If the vehicle is equipped with VTSS, use the DRBIII® and enable VTSS.
  5. Program all other options as needed.
  6. If any actuators were replaced in the HVAC System, with the DRBIII® in HVAC, select System Tests then select HVAC Door Recalibration (manual temperature system only).
  7. If any actuators were replaced in the ATC System, with the DRBIII® in Automatic Temp Control, select Miscellaneous then select Reset ATC Head.
  8. For Three-Zone HVAC Systems, if HVAC Control/Rear Blower Rear Control was replaced/Rear Blend Pot Circuit Open/Short DTC was set/any rear blend pot circuit was repaired, proceed to the next step. Otherwise, proceed to step  11.
  9. With DRBIII® in HVAC, select System Tests, then select HVAC Door Recalibration. Door Recalibration must pass before proceeding to next step.
  10. With DRBIII® in HVAC, select System Tests then select Reset Rear Blend Switch Span. Rotate Rear Blend/Mode control on Rear Blower Rear Control to full cold. Wait five seconds, then rotate control to full hot.
  11. If any repairs were made to the power sliding door or power liftgate, use the DRBIII® and perform the open and close system tests. Observe the instructions on the DRBIII® screen. Proceed to step  15.
  12. Obtain the vehicle's unique PIN assigned to it's original SKIM from either the vehicle's invoice or from Chrysler's Customer Assistance Center (1-800-992-1997).
    13. NOTE: Once Secured Access Mode is active, the SKIM will remain in that mode for 60 seconds.
  13. With the DRBIII®, select THEFT ALARM, SKIM, MISCELLANEOUS and select SKIM REPLACED. Enter the 4 digit PIN to put the SKIM in Secured Access Mode.
  14. The DRBIII® will prompt for the following steps:
    • Program the country code into the SKIM's memory.
    • Program the vehicle's VIN into the SKIM memory.
    • Transfer the vehicle's Secret Key data from the PCM.
  15. Using the DRBIII®, program all customer keys into the SKIM memory. This requires that the SKIM be in Secured Access Mode, using the 4 digit PIN.
    16. NOTE: If the PCM or ECM is replaced, the VIN and the unique Secret Key data must be transferred from the SKIM to the PCM or ECM. This procedure requires the SKIM to be placed in Secured Access Mode using the 4-digit PIN.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.