2002 Chrysler Voyager ECFACTORY OEM SERVICE PROCEDURE

ATC Head LED(S)/Back Lighting Inoperative

NOTE: After making any repairs, perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
  1. Turn the ignition on. With the DRBIII®, read ATC DTC's. If the DRBIII® displays any ATC DTCs, return to the DIAGNOSTIC TROUBLE CODE IDENTIFICATION table and choose the symptom(s). See DIAGNOSTIC TROUBLE CODE IDENTIFICATION  table. With the DRBIII®, reset the ATC after repair/replacement is complete. If the DRBIII® does not display any ATC DTCs, go to the next step.
  2. Turn the ignition on. With the DRBIII®, read the BCM DTCs. If the DRBIII® displays Headlamp Switch: Mismatch; STG; Open; or Panel Dim Output Short, refer to symptoms HEADLIGHT SWITCH MISMATCH , HEADLIGHT SWITCH SHORT TO GROUND , and HEADLIGHT SWITCH OPEN  under EXTERIOR LIGHTING. Refer to symptom PANEL DIMMING OUTPUT SHORT  under INSTRUMENT CLUSTER. With the DRBIII®, reset the ATC after repair/replacement is complete. If the DRBIII® does not display Headlamp Switch: Mismatch; STG; Open; or Panel Dim Output Short, go to the next step.
    3. NOTE: Compare with a known good ATC Head.
  3. Turn the ignition on. Turn the ATC Power switch on. Operate all ATC switches (Front Fan, Rear System, Temp, Mode, A/C, Recirc, Rear Defog) while looking at the display and lights on the ATC Head. If all of the LEDs operating properly, go to the next step. If all of the LEDs are not operating properly, replace the ATC. See A/C-HEATER CONTROL PANEL  under REMOVAL & INSTALLATION. With the DRBIII®, reset the ATC after repair/replacement is complete.
  4. Turn the ignition off. Rotate the Panel Lamps Dimmer switch to the off position. Disconnect the ATC C2 harness connector. See Figure. Turn the park lamps on. Measure the voltage of the Panel Lamps Driver circuit while rotating the Panel Lamps Dimmer switch from the off position to the full brightness position. If the voltage changes from approximately 2.5 volts to 11.5 volts, replace the ATC. See A/C-HEATER CONTROL PANEL  under REMOVAL & INSTALLATION. With the DRBIII®, reset the ATC after repair/replacement is complete. If the voltage does not change from approximately 2.5 volts to 11.5 volts, go to the next step.
  5. Turn the ignition off. Disconnect the ATC C2 harness connector. See Figure. Disconnect the Body Control Module C4 harness connector. See Figure. Measure the resistance of the Panel Lamps Driver circuit between the ATC C2 harness connector and the Body Control Module C4 harness connector. If the resistance is below 5 ohms, replace the Body Control Module. See BODY CONTROL MODULE  under REMOVAL & INSTALLATION. With the DRBIII®, reset the ATC after repair/replacement is complete. If the resistance is above 5 ohms, repair the Panel Lamps Driver circuit for an open. With the DRBIII®, reset the ATC after repair/replacement is complete.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.