Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Chrysler Intrepid BaseFACTORY OEM SERVICE PROCEDURE
Automatic Transmission DTCS
AUTOMATIC TRANSMISSION DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description |
|---|---|
| P0120 | THROTTLE POSITION SENSOR SIGNAL CIRCUIT |
| P0218 | HIGH TEMPERATURE OPERATION ACTIVATED |
| P0562 | LOW BATTERY VOLTAGE |
| P0604 | INTERNAL TCM |
| P0605 | INTERNAL TCM |
| P0613 | INTERNAL TCM |
| P0706 | CHECK SHIFTER SIGNAL |
| P0715 | INPUT SPEED SENSOR ERROR |
| P0720 | OUTPUT SPEED SENSOR ERROR |
| P0725 | ENGINE SPEED SENSOR CIRCUIT |
| P0731 | GEAR RATIO ERROR IN 1ST |
| P0732 | GEAR RATIO ERROR IN 2ND |
| P0733 | GEAR RATIO ERROR IN 3RD |
| P0734 | GEAR RATIO ERROR IN 4TH |
| P0736 | GEAR RATIO ERROR IN REVERSE |
| P0740 | TORQUE CONVERTER CLUTCH CONTROL CIRCUIT |
| P0750 | L-R SOLENOID CIRCUIT |
| P0755 | 2-4 SOLENOID CIRCUIT |
| P0760 | OD SOLENOID CIRCUIT |
| P0765 | UD SOLENOID CIRCUIT |
| P0841 | L-R PRESSURE SWITCH SENSE CIRCUIT |
| P0845 | 2-4 HYDRAULIC PRESSURE TEST FAILURE |
| P0846 | 2-4 PRESSURE SWITCH SENSE CIRCUIT |
| P0850 | PARK/NEUTRAL SWITCH PERFORMANCE |
| P0870 | OD HYDRAULIC PRESSURE TEST FAILURE |
| P0871 | OD PRESSURE SWITCH SENSE CIRCUIT |
| P0884 | POWER-UP AT SPEED |
| P0888 | RELAY OUTPUT ALWAYS OFF |
| P0890 | SWITCHED BATTERY |
| P0891 | RELAY OUTPUT ALWAYS ON |
| P0897 | WORN OUT/BURNT TRANSMISSION FLUID |
| P0944 | LOSS OF PRIME |
| P0951 | AUTOSTICK SWITCH CIRCUIT |
| P0992 | 2-4/OD HYDRAULIC PRESSURE TEST FAILURE |
| P1652 | SERIAL COMMUNICATION LINK MALFUNCTION |
| P1684 | BATTERY WAS DISCONNECTED |
| P1687 | NO COMMUNICATION WITH MIC |
| P1694 | BUS COMMUNICATION WITH PCM |
| P1775 | SOLENOID SWITCH LATCHED IN TCC POSITION |
| P1776 | SOLENOID SWITCH LATCHED IN L-R POSITION |
| P1790 | FAULT IMMEDIATELY AFTER SHIFT |
| P1794 | SPEED SENSOR GROUND ERROR |
| P1797 | MANUAL SHIFT OVERHEAT |
| P1799 | CALCULATED OIL TEMPERATURE IN USE |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.