2002 Chrysler Intrepid BaseFACTORY OEM SERVICE PROCEDURE

Passenger Mirror Vertical Sensor Out Of Range Low

NOTE: After making any repairs, perform MEMORY HEATED SYSTEM VERIFICATION TEST  under VERIFICATION TESTS.

Monitored & Set Condition

  1. When Monitored: Ignition on.
  2. Set Condition: This code is set when the mirror sensor feedback to the MHSMM is less than the mirror out of range low value stored in EEPROM.

Possible Causes:

  • MHSMM 5-Volt Supply
  • 5-Volt Supply To Mirror
  • Mirror Vertical Circuit Check
  • Passenger Mirror 5-Volt Supply Open
  • Passenger Mirror Vertical Position Signal Wire Open
  • Passenger Mirror Vertical Position Signal Wire Short To Ground
  • Passenger Memory Mirror

Testing

  1. Turn ignition off. Disconnect Memory Heated Seat/Mirror Module (MHSMM) connector C1. Turn ignition on. Measure voltage on MHSMM connector C1 terminal No. 6, passenger mirror vertical position signal circuit (Yellow/Red wire). See Figure . If voltage is 4.5-5.0 volts, replace MHSMM. See MEMORY HEATED SEAT/MIRROR MODULE  under REMOVAL & INSTALLATION. If voltage is less than 4.5-5.0 volts, leave MHSMM connector C1 disconnected and go to next step.
  2. Turn ignition off. Disconnect passenger mirror connector. Measure resistance of passenger mirror vertical position signal circuit (Yellow/Red wire) between driver mirror connector terminal No. 7 and MHSMM connector C1 terminal No. 6. See Figure . If resistance is less than 5 ohms, leave connectors disconnected and go to next step. If resistance is 5 ohms or more, repair open in Yellow/Red wire.
  3. Measure resistance between ground and passenger mirror connector terminal No. 7, passenger mirror horizontal position signal circuit (Yellow/Red wire). If resistance is less than 1000 ohms, repair short to ground in Yellow/Red wire. If resistance is 1000 ohms or more, leave passenger mirror connector disconnected and go to next step.
  4. Ensure MHSMM connector is properly connected. Turn ignition on. Measure voltage on passenger mirror connector terminal No. 6, passenger mirror sensor 5-volt supply circuit (Gray/White wire). If voltage is 4.5-5.0 volts, replace passenger mirror. See appropriate POWER MIRROR article. If voltage is not 5.5-5.0 volts, leave passenger mirror connector disconnected and go to next step.
  5. Turn ignition off. Disconnect MHSMM connector C2. Measure resistance of passenger mirror sensor 5-volt supply circuit (Gray/White wire) between passenger mirror connector terminal 6 and MHSMM connector C2 terminal No. 8. If resistance is less than 5 ohms, replace MHSMM. See MEMORY HEATED SEAT/MIRROR MODULE  under REMOVAL & INSTALLATION. If resistance is 5 ohms or more, repair open in Gray/White wire.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.